Business > Industrial Devices > Automation Controls Top > Components & Devices > Relays / Couplers > Power Relays (Over 2A) > Power Relays (Over 2A) Lineup > HE-S Relays > Cautions For Use

HE-S Relays

Lineup
- DE Relays Compliant with European safety standards, 1 Form A/2 Form A/1 Form A 1 Form B 10 A/8 A Polarized power relays
- DJ Relays High insulation, 1-pole/2-pole 16 A, Polarized power relays
- DJ-H Relays Suitable for lighting and motor load, 1 Form A 50 A, Latching relays
- DK Relays 1 Form A 10 A, 1 Form A 1 Form B/2 Form A 8 A, Small polarized power relays
- DS Power Relays 1 Form A 8 A (AC) / 5 A (DC) , 1 Form A 1 Form B/2 Form A 5 A (AC/DC) , Small polarized power relays
- DW Relays 1 Form A 8 A/16 A, Small, Polarized power relays (latching type)
- DY Relays 1 Form A 10 A, 1 Form A 1 Form B 8 A, Small polarized power relays
- DZ-S Relays IEC62055-31 UC3 compliant, 1 Form A 90 A, Power latching relays
- HE Relays TV-10/TV-15 rated, 1 Form A 30 A, 2 Form A 25 A, Power relays
- HE Relays PV Type Compact size, 1 Form A 35 A/48 A/90 A Power relays for solar inverter
- HE-N Relays High capacity 120 A　490 V AC 1 Form A power relay
- HE-S Relays Compact size 2a and 2a1b 40 A power relays for energy management and industrial equipment
- HE-R Relays Compact size 2 Form A and 2 Form A 1Form B 80 A/4 Form A and 4 Form A and 1 Form B 40 A power relays
- JV-N Relays 1 Form A 16 A, low profile: 10.9 mm power relays for heater control
- JW Relays 1 Form A/1 Form C/2 Form A/2 Form C, 5 A/10 A, Power relays
- LD-P Relays Compliant with IEC/EN60335-1/ EN60079-15 (VDE approved) 1 Form A 5 A Slim power relays
- LF Relays Ideal for compressor and inverter loads, 1 Form A 20 A, Power relays
- LF-G Relays Load for solar inverter, Compact size, 1 Form A 22 A/33 A, Power relays
- LQ Relays Compliant with IEC/EN60335-1^*1^*2 /EN60079-15^*3 (VDE approved) 1 Form A/1 Form C 10A small power relays
- LZ Relays Low profile: 15.7 mm, 1 Form A/1 Form C 16 A, Power relay
- LZ-N Relays EN60335-1 GWT compliant, 15.7 mm Low profile, 1 Form A/1 Form C 16 A, Power relays
- NC Relays Transistor drive, 2 Form C/4 Form C, 5 A Slim power relays
- PA-N Relays Complies with IEC61010 reinforced insulation, For PLC/Interface, 1 Form A 5 A, Slim power relay
- PF Relays Compliant with European standards, 1 Form A/1 Form C 6 A, Slim power relays
- S Relays 2 Form A 2 Form B/3 Form A 1 Form B/4 Form A /4 A Polarized power relays
- SP Relays 2 Form C 15 A, 4 Form C 10 A, Polarized power relays
- ST Relays 1 Form A 1 Form B/2 Form A, 8 A, Polarized power relays
CAD data　 Catalogs/Datasheets　　
FAQ

Click here for information on compliance with standards

Cautions For Use

HE-S Relays Cautions for Use

1. For cautions for use, please refer to our web site.

2. When coil holding voltage controlled by PWM, check coil holding voltage and operation of relay under the actual condition.

3. Usage, transport and storage conditions

1.Temperature:
–40 to +55°C –40 to +131°F(When applied coil holding voltage is 30% to 110%V of nominal coil voltage)
–40 to +85°C –40 to +185°F(When applied coil holding voltage is 30% to 60%V of nominal coil voltage or storage)
2.Humidity: 5 to 85% RH (Not freezing and condensing at low temperature)
In addition the humidity range depends on temperature. The allowable ranges are as follows;
3.Air pressure: 86 to 106 kPa

Allowable range of temperature and humidity for operation, transport and storage.

[Coil holding voltage: 30% to 110%V]

[Coil holding voltage: 30% to 60%V]

4. Solder and cleaning conditions

1.Please obey the following conditions when soldering automatically.

1.Pre-heating: within 120°C 248°F(solder surface terminal portion) and within 120 seconds
2.Soldering iron: 260°C±5°C 500°F±41°F(solder temperature) and within 10 seconds (soldering time)

2.In case of manual soldering, following conditions should be observed.

Max. 270°C 518°F (solder temperature) within 10 seconds (soldering time)
Max. 350°C 662°F (solder temperature) within 5 seconds (soldering time)

* Effects of soldering heat on the relays vary depending on the PC board. So please confirm actual soldering condition with the PC board used for assembling.