AUTOMATION
CONTROLS

Search
Discontinued
Products



WH

Specifications

Main unit specifications

Type Standard model
4.3 inch 7 inch 10.1 inch
Part No. AWHS1R043 AWHS1R070 AWHS1R101
Regulatory compliance EMC Directive, RoHS Directive, UL/c-UL Listing certification, Korea Radio Wave Regulations (Radio Wave Act KC)
Rated Voltage 24V DC
Operating voltage range 10 to 32 V DC
Current consumption (at 24 V DC) 0.25 A or less 0.3 A or less 0.38 A or less
Ambient temperature 0 to +50 ℃ +32 to +122 ℉ (Note 1),
Storage -20 to +70 ℃ -4 to +158 ℉
Ambient humidity 5 to 85% RH (at +25 ℃ +77 ℉, No condensation or icing allowed, Same when storing)
Vibration resistance 5 to 9 Hz, 3.5 mm 0.138 in single amplitude, 9 to 150 Hz, Acceleration 9.8 m/s2 (1 G)
Shock resistance 490 m/s2 (50 G), 11 ms, 3 times in the X, Y, Z directions
Protection Front panel: IP66 (Initial value) (Note 2), Rear: IP20
Pollution degree 2
Net Weight 0.4 kg approx. 0.6 kg approx. 1 kg approx.

Notes:

1) In vertical installation conditions
2) The IP66 is guaranteed only if:
・Max deviation from the plane surface to the cut-out: ≤ 0.5 mm 0.020 in
・Thickness of the case where is mounted the equipment: from 1.5 mm to 6 mm 0.059 in to 0.236 in
・Max surface roughness where the gasket is applied: ≤ 120 μm
Also, tightening torque: 0.75 N•m (for advanced type: 1.3 N•m) or screw each fixing screw until the bezel corner gets in contact with the panel.

Type Advanced model
5 inch 7 inch 10.1 inch 15.6 inch 21.5 inch
Part No. AWHA1C050 AWHA1C070 AWHA1C101 AWHA1C156 AWHA1C215
Regulatory compliance EMC Directive, RoHS Directive, UL/c-UL Listing certification, Korea Radio Wave Regulations (Radio Wave Act KC)
Rated Voltage 24V DC
Operating voltage range 10 to 32 V DC (Note 1)
Current consumption (at 24 V DC) 0.6 A or less 0.7 A or less 1 A or less 1.2 A or less 1.7 A or less
Ambient temperature -20 to +50 ℃ -4 to +122 ℉ (Note 2),
Storage -20 to +70 ℃ -4 to +158 ℉
Ambient humidity 5 to 85% RH (at +25 ℃ +77 ℉, No condensation or icing allowed, Same when storing)
Vibration resistance 5 to 9 Hz, 3.5 mm 0.138 in single amplitude, 9 to 150 Hz, Acceleration 9.8 m/s2 (1 G)
Shock resistance 490 m/s2 (50 G), 11 ms, 3 times in the X, Y, Z directions
Protection Front panel: IP66 (Initial value) (Note 3), Rear: IP20
Pollution degree 2
Net Weight 1 kg approx. 1.3 kg approx. 2.5 kg approx. 4.1 kg approx. 6.1 kg approx.

Notes:

1) The voltage tolerance range for maintaining a 10 ms voltage dips is limited to 20.4 to 32 V DC. * Does not include connection of external devices.
2) In vertical installation conditions
3) The IP66 is guaranteed only if:
・Max deviation from the plane surface to the cut-out: ≤ 0.5 mm 0.020 in
・Thickness of the case where is mounted the equipment: from 1.5 mm to 6 mm 0.059 in to 0.236 in
・Max surface roughness where the gasket is applied: ≤ 120 μm
Also, tightening torque: 0.75 N•m (for advanced type: 1.3 N•m) or screw each fixing screw until the bezel corner gets in contact with the panel.

Function specifications

Type Standard model Advanced model
Displayable fonts Fixed font, True Type font, Fonts installed in Windows® (Note 1) (Note 2)
Number of registerable screens (pages) (Note 3) Max. 1,000
Registerable screen number Pages: 1,000
Dialog: 50
Template: 50
Types of widget Basic (text, numerics), Button, Meter, Switch, Light, Media, Icon, Custom, etc.
Main functions Trends, Reports, Alarms, Scheduler, Database, Data transfers, Recipe, Keypads, Web Server, etc.
Through function If a PC is connected to the LAN port of a WH series and a PLC is connected into the serial port, the PLC program can be debugged without a direct connection between the computer and the PLC. (Note 4)

Notes:

1) Windows is a registered trademark of Microsoft Corporation in the United States and other countries.
2) A license (permission to use) is required to add the font.
3) Maximum allowable number varies depending on registered contents.
4) The only supported PLC is our FP series.

Performance specifications

Type Standard model
4.3 inch 7 inch 10.1 inch
Part No. AWHS1R043 AWHS1R070 AWHS1R101
Display Display unit 4.3 inch wide TFT 7 inch wide TFT 10.1 inch wide TFT
Resolution 480 × 272,
WQVGA
800 × 480,
WVGA
1,024 × 600,
WSVGA
Displayable area 96.4 × 55.2 mm
3.795 × 2.173 in
155.5 × 88 mm
6.122× 3.465 in
224.3 × 126.8 mm
8.831 × 4.992 in
Colors 65,536 colors
Backlight White LED
Backlight
brightness (Initial)
200 cd/m2 (typ.)
Dimming Yes (Can be adjusted on the menu screen, xAscender Studio settings.
*There are some minor variations in the backlight brightness.
Backlight life time 20,000 hours or more (Note 2)
Touch
switch
Touch switch Analog resistive film type
Touch switch operating 1.5 N or less
Life time 1 million times or more (Note 3)
Memory
space
RAM 512 MB
Flash memory 4 GB
Project memory 240 MB
User memory 512 MB
RTC /
Backup
Clock function Yes
Accuracy RTC ±100 ppm or less (at +25 ℃ +77 ℉) (Note 4)
Backup range Clock back up
Backup function /
period
48h with super capacitor backup
(at +25 ℃ +77 ℉) (Note 5)
Other Buzzer

Notes:

1) On the LCD panel, bright spots (points always lit) or black spots (points always unlit) may appear, or the uneven brightness, flickers or crosstalk (appearance of unintended shades in the area no graphic or part is arranged) may occur depending on the operating conditions.
Note that these phenomena are resulted from the basic characteristics of LCD panel not defects or failures of the product.
2) Time of continuous operation until the brightness of the backlight reaches 50% of the rated value when the surrounding air temperature is +25 ℃ +77 ℉
3) The touch position may shift due to aging variation. If the touch position has shifted greatly, please adjust it.
4) At +25 ℃ +77 ℉: less than 260 seconds per month. On systems prone to clock error, set the correct time on a regular basis.
5) Must be charged for 48 hours. When the battery is fully charged, it ensures a period of 48 hours of data backup.

Type Advanced model
5 inch 7 inch 10.1 inch 15.6 inch 21.5 inch
Part No. AWHA1C050 AWHA1C070 AWHA1C101 AWHA1C156 AWHA1C215
Display Display unit 5 inch
wide TFT
7 inch
wide TFT
10.1 inch
wide TFT
15.6 inch
wide TFT
21.5 inch
wide TFT
Resolution 800 × 480,
WVGA
800 × 480,
WVGA
1,280 × 800,
WXGA
1,366 × 768,
HD
1,920 × 1,080,
Full HD
Displayable area 109 × 65.8 mm
4.291 × 2.591 in
152.6 × 91.6 mm
6.008 × 3.606 in
217.9 × 136.6 mm
8.579 × 5.378 in
345.5 × 195 mm
13.602 × 7.677 in
478 × 269.5 mm
18.819 × 10.610 in
Colors 65,536 colors 16,770,000 colors
Backlight White LED
Backlight
brightness (Initial)
300 cd/m2 (typ.) 500 cd/m2 (typ.) 400 cd/m2 (typ.) 300 cd/m2 (typ.)
Dimming Yes (Can be adjusted on the menu screen, xAscender Studio settings.
*There are some minor variations in the backlight brightness.
Backlight life time 40,000 hours or more (Note 2)
Touch
switch
Touch switch Capacitive type
Touch switch operating -
Life time -
Memory
space
RAM 512 MB 1 GB 1 GB 2 GB 2 GB
Flash memory 4 GB 4 GB 4 GB 8 GB 8 GB
Project memory 240 MB
User memory 512 MB
RTC /
Backup
Clock function Yes
Accuracy RTC ±100 ppm or less (at +25 ℃ +77 ℉) (Note 3)
Backup range Clock back up
Backup function /
period
3 months with lithium batteries (secondary batteries)
(at +25 ℃ +77 ℉) (Note 4)
Other Buzzer

Notes:

1) On the LCD panel, bright spots (points always lit) or black spots (points always unlit) may appear, or the uneven brightness, flickers or crosstalk (appearance of unintended shades in the area no graphic or part is arranged) may occur depending on the operating conditions.
Note that these phenomena are resulted from the basic characteristics of LCD panel not defects or failures of the product.
2) Time of continuous operation until the brightness of the backlight reaches 50% of the rated value when the surrounding air temperature is +25 ℃ +77 ℉
3) At +25 ℃ +77 ℉: less than 260 seconds per month. On systems prone to clock error, set the correct time on a regular basis.
4) Must be charged for 48 hours. When the battery is fully charged, it ensures a period of 48 hours of data backup.

Interface specifications

Ethernet port communication specifications

Type Standard model
4.3 inch 7 inch 10.1 inch
Part No. AWHS1R043 AWHS1R070 AWHS1R101
Number of
communication ports
1 port
Interface 100BASE-TX / 10BASE-T
Baud rate 100 Mbps / 10 Mbps, Auto negotiation (Note 2)
Connecter shape RJ-45 (Note 3)
Cable total length 100 m 328.084 ft (500 m 1,640.42 ft when using a repeater) (Note 4)
Communication cable UTP cable (Category 5 or higher)
Number of web client simultaneous connections Max. 4
communication method Full-duplex / Half-duplex
communication protocol TCP/IP, UDP/IP
DNS Name server support
DHCP Correspondence of automatic IP address acquisition
FTP server / client Server function: Transfer file / Client function: Transfer data and file
HTTP server / client Server function: Customer web / Client function: Web browser
SNTP Correspondence of time setting function

Notes:

1) Ethernet is a registered trademark of FUJIFILM Business Innovation Corp. and Xerox Corp.
2) Switching between different speeds is done automatically by auto negotiation function.
3) Be careful not to apply excessive static electricity to the metal parts of the connector.
4) The maximum length of the cable is 100 m 328.084 ft in accordance with the standards, but depending on the operating environment, a ferrite core may be installed to reduce noise. May be required. It is also recommended that the hub be installed near the control panel and that it be used at 10 m 32.808 ft or less.

Type Advanced model
5 inch 7 inch 10.1 inch 15.6 inch 21.5 inch
Part No. AWHA1C050 AWHA1C070 AWHA1C101 AWHA1C156 AWHA1C215
Number of
communication ports
2 ports 3 ports
Interface 100BASE-TX / 10BASE-T
Baud rate 100 Mbps / 10 Mbps, Auto negotiation (Note 2)
Connecter shape RJ-45 (Note 3)
Cable total length 100 m 328.084 ft (500 m 1,640.42 ft when using a repeater) (Note 4)
Communication cable UTP cable (Category 5 or higher)
Number of web client simultaneous connections Max. 4
communication method Full-duplex / Half-duplex
communication protocol TCP/IP, UDP/IP
DNS Name server support
DHCP Correspondence of automatic IP address acquisition
FTP server / client Server function: Transfer file / Client function: Transfer data and file
HTTP server / client Server function: Customer web / Client function: Web browser
SNTP Correspondence of time setting function

Notes:

1) Ethernet is a registered trademark of FUJIFILM Business Innovation Corp. and Xerox Corp.
2) Switching between different speeds is done automatically by auto negotiation function.
3) Be careful not to apply excessive static electricity to the metal parts of the connector.
4) The maximum length of the cable is 100 m 328.084 ft in accordance with the standards, but depending on the operating environment, a ferrite core may be installed to reduce noise. May be required. It is also recommended that the hub be installed near the control panel and that it be used at 10 m 32.808 ft or less.

Serial port communication specifications (Same for both standard and advanced models)

Type RS-232C RS-422 / RS-485
Communication standard Conforms to RS-232C (Non insulation type) Conforms to RS-422 / RS-485 (Non insulation type)
Number of communication ports 1 port *Can be switched with xAscender Studio
Conditions for communication with external devices Baud rate 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 bit/s (Note 1)
Data bits 7 bits / 8 bits
Parity none / even / odd
Stop bit 1 bit / 2 bit
Transmission distance
(Total length)
Max. 15 m 49.213 ft (for advanced model: Max. 15 m 49.213 ft)
(Baud rate: 19,200 bps)
Max. 500 m 1,640.42 ft (Baud rate: 115.2 kbps)
Terminal resistance - No termination (Note 2)
Connector D-Sub 9 pins (Note 3) (Connector supplied with advanced model)

Notes:

1) Communication conditions depend on the communications state of PLCs or other slave devices. Please check with the actual devices when some commercial devices with RS485 interface are connected. The number of connected devices, transmission distance, and transmission speed may be different according to using transmission line.
2) When connected to the termination, it is recommended that a 120Ω, 1/2W or better termination resistor be connected between the communication lines.
3) Use standard commercially available 9-pin D-sub male connector.

USB port specifications

Type Standard model
4.3 inch 7 inch 10.1 inch
Part No. AWHS1R043 AWHS1R070 AWHS1R101
Number of ports 1 port
USB specifications USB Host
Electrical specifications Complies with USB 2.0
Connector shape USB Type A (Note 1)
Transmission speed 480 Mbps (High speed mode)
Maximum current Max. 500 mA

Notes:

1) Take care of handling of the connector not to add an excessive static electricity on the metal part of the connector.
2) The format of the external memory should be in FAT32 or FAT. The max number of files inside external memory depends on the type of formatting. (Supports up to 32 GB capacity.)
• FAT32: Max. 65,535 files
• FAT: Max. 512 files

Type Advanced model
5 inch 7 inch 10.1 inch 15.6 inch 21.5 inch
Part No. AWHA1C050 AWHA1C070 AWHA1C101 AWHA1C156 AWHA1C215
Number of ports 1 port 2 ports
USB specifications USB Host
Electrical specifications Complies with USB 2.0
Connector shape USB Type A (Note 1)
Transmission speed 480 Mbps (High speed mode)
Maximum current Max. 500 mA

Notes:

1) Take care of handling of the connector not to add an excessive static electricity on the metal part of the connector.
2) The format of the external memory should be in FAT32 or FAT. The max number of files inside external memory depends on the type of formatting. (Supports up to 32 GB capacity.)
• FAT32: Max. 65,535 files
• FAT: Max. 512 files

SD memory card specifications

Standard model is not compatible with SD memory card.

Type Advanced model
5 inch 7 inch 10.1 inch 15.6 inch 21.5 inch
Part No. AWHA1C050 AWHA1C070 AWHA1C101 AWHA1C156 AWHA1C215
Support media SD memory card, SDHC memory card (Note 1)
Supported
format standard
Conforms to SD standard (Note 2)
(Please format with a format software for SD memory cards.)

Notes:

1) Industrial or business use SD memory cards (SLC type) are recommended. Check the operating temperature range of the SD memory card before use.
2) The format of the external memory should be in FAT32 or FAT. The max number of files inside external memory depends on the type of formatting. (Supports up to 32 GB capacity.)
• FAT32: Max. 65,535 files
• FAT: Max. 512 files

Return to top

CONTACT US
If you have any questions, please select the option below to contact us or find answers.
CONTACT BY EMAIL / PHONE FIND LOCAL OFFICE

Return to top

CONTACT US
BY EMAIL
Please click your area to select country or region




Requests to customers (Automation Control Components & Industrial Device) [Excluding specific product]
Requests to customers (Automation Control Components & Industrial Device) [For specific product]
Requests to customers (FA Sensors & Components [Excluding motors])
Requests to customers (Dedicated to industrial motors)