AUTOMATION
CONTROLS

Search
Discontinued
Products



Compact CO2 Laser Marker LP-GS SERIES

Revolutionary compact size

LP-GS
CE Marking Korean KC FDA

CE , Korean KC , FDA Approved

Features

Revolutionary size

Minimized head size contributes to floor space cost reduction.

Downsized unit
The LP-GS series Laser Marker heads have considerably decreased in size. The controller is also miniaturized so this downsized unit contributes to reduce floor space cost.
Heads can be installed in any direction (Vertical, Horizontal), allowing users design their equipment more flexible.

Downsized unit

Marking on a wide area
The LP-GS series head ensures both miniature size with light weight. Moving the head to the marking position ensures high-quality marking over a wide area. Due to the smaller head size, less space for installation is required, even when marking on an M- or L-sized large circuit board. The cable between head and controller is flex-resistant.

Marking on a wide area

Please note that exess force should not be applied when moving the head.

Production improvements

Drastic improvements in marking quality and man-hours for setup change

Marking on circuit boards with various thickness
Previously the head height had to be adjusted each time the circuit board thickness was changed. LP-GS series have integrated Z-axis control mechanism which allow adjustment of the work distance based on circuit board thickness.The mechanism both eliminates man-hours to change setup and maintains marking quality stability.

[Example of height control via Z-axis control]

Example of height control via Z-axis control
With Z-axis adjustment
With Z-axis adjustment
Without adjustment
Without adjustment
As marking on a circuit board, its quality of marking might be different depending on the thickness of resist.
Please be sure to carry out the marking test beforehand and check its quality.
For the method of testing, please contact each area sales in charge.

This Z-axis control mechanism helps to improve the production efficiency when marking on not only substrates but also workpieces of various sizes.

IC

IC

Connector

Connector

Connector

Connector

Camera correction without PLC
A camera can be used for adjusting the tilt of the work piece to maintance the marking quality.
Connect the LP-GS series and the camera directly to transfer the correction data from camera to the Laser Marker. In addition, man-hours for PLC programming can be reduced.

Camera correction without PLC

Easy setting

Laser Marker NAVI smart

Using the software, characters, logo marks, and 2D code can be set and arranged on a PC or tablet. The screen layout can be customized to suit each work environment. The screen can be switched according to the purpose of use, such as for parameter setting or for workers.

Laser Marker NAVI smart

【Smart condition setting function】
The one-touch function is packed with our extensive know-how of laser marking parameters such as laser power, scan speed and pulse oscillation frequency. The user can select a desired marking result from 6 types of material and image.

Smart condition setting function

Many convenient functions

"External device link function" - controllable without PLC

Previously, a PLC was required in order to coordinate the Laser Marker with image processing devices and readers. The LP-GS series is capable of direct data processing with certain devices even without a PLC, thanks to the external device link function.


[Link with an image processing device]

<Position adjustment marking>
The Laser Marker is equipped with a new function that provides direct control of an image processing device (IPD). Now the Laser Marker itself can trigger the IPD to send the workpiece position (coordinate data). As there is no need for a PLC and programming, the amount of man-hours is reduced.

Link with an image processing device

<Read and collate marking data>
A new function has been added which enables to control a sequence of operations from marking to reading the code. The reader (IPD) reads codes marked by the Laser Marker and collates them with the original data to check whether the code is correctly marked.
This helps to prevent mixup of incorrectly marked products.
The reader (image processing device) reads code marked by the Laser Marker and the Laser Marker collate it with the original data to check whether the code is correctly marked, in order to prevent mixup of incorrectly marked products.

Read and collate marking data

[Link with a code reader]
The laser marker can be controlled by reading code.

Connect the laser marker and code reader directly and read data, such as production instruction, etc. Based on this information, the Laser marker can execute various operations configured beforehand, e.g. change the marking data. Laser Marker controled by code data prevents input error by operator.

Link with a code reader


Discontinued products [Order accepted till September, 2021]

Discontinued product Recommended substitute
Product number/Part number Last time buy   Product number/Part number Product name Remark
Product number: LP-GS052-F
Part number: LP-GS052-F
September 30, 2021
To be discontinued
Product number:-
Part number:-
- Sorry, no suggested alternative products.
Product number: LP-GS052-FE
Part number: LP-GS052-FE
September 30, 2021
To be discontinued
Product number:-
Part number:-
- Sorry, no suggested alternative products.
Product number: LP-GS052-FN
Part number: LP-GS052-FN
September 30, 2021
To be discontinued
Product number:-
Part number:-
- Sorry, no suggested alternative products.

Return to top

CONTACT US
If you have any questions, please select the option below to contact us or find answers.
CONTACT BY EMAIL / PHONE FIND LOCAL OFFICE SEARCH FAQ

Return to top

CONTACT US
BY EMAIL
Please click your area to select country or region



BY PHONE

FAQ


Requests to customers (Automation Control Components & Industrial Device) [Excluding specific product]
Requests to customers (Automation Control Components & Industrial Device) [For specific product]
Requests to customers (FA Sensors & Components [Excluding motors])
Requests to customers (Dedicated to industrial motors)