Digital Fiber Sensor FX-100

Order guide

Amplifiers

Note :

1)The connector attached cable 2 m 6.562 ft CN-14A-C2 is supplied with the amplifier.

2)Make sure to use the optional connector attached cable CN-14A(-R)-C□ or the connector CN-14A, or a connector manufactured by J.S.T. Mfg. Co., Ltd.
(contact: SPHD-001T-P0.5, housing: PAP-04V-S)

3)Make sure to use the optional M8 connector attached cable CN-24A-C□.

Accessory

CN-14A-C2

(Connector attached cable 2 m6.562 ft)* Only include cable set type

FC-FX-1
(Protection cover)

*It have been attached from the production at July, 2011.

Option

Note : The connector attached cable CN-14A-C2 is supplied with the cable set type FX-10□-CC2.

M8 connector attached cable

CN-24A-C□

Amplifier mounting bracket

MS-DIN-4

Connector attached cable

CN-14A(-R)-C□

Connector

CN-14A

Recommended connector

Contact:
SPHD-001T-P0.5, Housing: PAP-04V-S (Manufactured by J.S.T. Mfg. Co., Ltd.)

Note:
Contact the manufacturer for details of the recommended products.

Recommended crimping tool

Model No.:
YC-610R (Manufactured by J.S.T. Mfg. Co., Ltd.)

Note:
Contact the manufacturer for details of the recommended products.

Recommended e-CON connector

Manufactured by 3M Japan Limited
Adapted connector : 37104-3122-000 FL

Please refer to "Introducing the 3M™ mini-clamp connector" for details.

Specifications

Notes:

1):Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.

2):When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values.
However, the interference prevention function does not operate at emission frequency 0 (factory default setting) for the FX-101(P)(-Z) / FX-101(P)-CC2.

3):The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.

4):Connector attached cable CN-14A-C2 is not attached to the models that have no "-CC2" at the end of the model Nos.
Make sure to use the optional connector attached cable CN-14A(-R)-C□ or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.
(contact: SPHD-001T-P0.5, housing: PAP-04V-S).

5):Model Nos. having the suffix "-Z" are M8 plug-in connector type. Make sure to use the optional M8 attached connector cable CN-24A-C□.

6):Protection cover FC-FX-1 has been attached from production in July, 2011.

Dimensions

• Unit: mm in

FX-101□
FX-102□

Amplifier

Note: The protection cover has been attached from the production at July, 2011.

FX-101(P)-Z
FX-102(P)-Z

Amplifier

Note: The protection cover has been attached from the production at July, 2011.

CN-14A-C□
CN-14A-R-C□

Connector attached cable (Optional, CN-14A-C2 is attached to FX-101(P)-CC2 / FX-102(P)-CC2)

• Length L

MS-DIN-4

Amplifer mounting bracket (Optional)

Material:PBT

MS-DIN-E

End plate (Optional)

Material:Polycarbonate

I/O Circuit and Wiring diagrams

NPN output type

FX-10□(-Z/-CC2)

I/O circuit diagram

Symbols･･･

D : Reverse supply polarity protection diode
Z_D: Surge absorption zener diode
Tr : NPN output transistor

Terminal arrangement diagram

Connector type

M8 plug-in connector type

PNP output type

FX-10□P(-Z/-CC2)

I/O circuit diagram

Symbols･･･

D : Reverse supply polarity protection diode
Z_D: Surge absorption zener diode
Tr : PNP output transistor

Terminal arrangement diagram

Connector type

M8 plug-in connector type

Sensing characteristics

Sensing characteristics can be downloaded at catalog download site.
Please contact our office if not listed here.

List of fibers

Fiber List

• Square Head Fiber
• Super Quality
• Threaded Type
• Cylindrical Type
• Sleeve

• Flat Type
• Narrow Beam
• Wide Beam
• Convergent Reflective Type
• Retroreflective Type

• Chemical-resistant
• Heat-resistant
• One-Touch Connection System Vacuum-resistant Fibers
• Vacuum-resistant
• Metal-free

Square Head Fiber

■Thru-beam type(one pair set)

■Reflective type

Note1:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending on how the fiber is cut.

Note2:The sensing range is specified for white non-glossy paper.

For details of Square Head Fiber, refer to product information page.
>>Go to "Square Head Fiber"

Super Quality

■Thru-beam type (one pair set)

■Reflective type

Note:The sensing range is specified for white non-glossy paper.

For details of Super Quality Fiber, refer to product information page.
>>Go to "Super Quality Fiber"

Threaded Type

■Thru-beam type (one pair set)

Note 1:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

Note 2:The fiber cable length practically limits the sensing range.

■Reflective type

Note 1:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

Note 2:The sensing range is specified for white non-glossy paper.

For details of Threaded Type Fiber, refer to product information page.
>>Go to "Threaded Type Fiber"

Cylindrical Type

■Thru-beam type (one pair set)

Note:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

■Reflective type

Note 1:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

Note 2:The sensing range is specified for white non-glossy paper.

For details of Cylindrical Type Fiber, refer to product information page.
>>Go to "Cylindrical Type Fiber"

Sleeve

■Thru-beam type (one pair set)

Note 1:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

Note 2:The fiber cable length practically limits the sensing range.

■Reflective type

Note 1:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

Note 2:The sensing range is specified for white non-glossy paper.

For details of Sleeve Fiber, refer to product information page.
>>Go to "Sleeve Fiber"

Flat Type

■Thru-beam type (one pair set)

Note:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

■Reflective type

Note 1:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

Note 2:The sensing range is specified for white non-glossy paper.

For details of Flat Type Fiber, refer to product information page.
>>Go to "Flat Type Fiber"

Narrow Beam

■Thru-beam type (one pair set)

Note 1:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

Note 2:The fiber cable length practically limits the sensing range.

■Retroreflective type

Note 1:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

Note 2:The sensing range is the possible setting range for the attached reflector. The fiber can detect an object less than setting range for the reflector.

■Reflective type

Note:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

For details of Narrow Beam Fiber, refer to product information page.
>>Go to "Narrow Beam Fiber"

Wide Beam

■Thru-beam type (one pair set)

Note 1:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

Note 2:The fiber cable length practically limits the sensing range to 3,600 mm long.

■Reflective type

Note 1:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

Note 2:The sensing range is specified for white non-glossy paper.

For details of Wide Beam Fiber, refer to product information page.
>>Go to "Wide Beam Fiber"

Convergent Reflective Type

■Reflective type

Note 1:The sensing range is specified for transparent glass 100 x 100 x t0.7 mm (FD-L32H: R edge, FD-L21 and FD-L21W: t2 mm) (FD-L20H: white non-glossy paper, FD-L10: silicon wafers 100 x 100 mm).

Note 2:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

For details of Convergent Reflective Type Fiber, refer to product information page.
>>Go to "Convergent Reflective Type Fiber"

Retroreflective Type

■Retroreflective type

Note 1:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

Note 2:The sensing range is the possible setting range for the attached reflector. The fiber can detect an object less than setting range for the reflector.

For details of Retroreflective Type Fiber, refer to product information page.
>>Go to "Retroreflective Type Fiber"

Chemical-resistant

■Thru-beam type (one pair set)

Note:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

Reflective type

Note 1:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending on how the fiber is cut.

Note 2:The sensing range is specified for white non-glossy paper.

For details of Chemical-resistant Fiber, refer to product information page.
>>Go to "Chemical-resistant Fiber"

Heat-resistant

■Thru-beam type (one pair set)

Note:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

■Reflective type

Note 1:The sensing range of reflective type is the value for white non-glossy paper (50 x 50 mm glass substrate for FD-H30-L32,
FD-H18-L31, transparent glass 100 x 100 x t0.7 mm for FD-H25-L43 and FD-H25-L45).

Note 2:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

For details of Heat-resistant Fiber, refer to product information page.
>>Go to "Heat-resistant Fiber"

One-Touch Connection System Vacuum-resistant Fibers

■Thru-beam type

(Note 1):Atmospheric side fiber, FT-J9 (optional) is free-cut type.
Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

■Reflective type

(Note 1):The sensing range is the value for transparent glass 100 × 100 × t0.7 mm 3.937 × 3.937 × t0.028 in.

(Note 2):Atmospheric side fiber, FT-J9 (optional) is free-cut type.
Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

For details of One-Touch Connection System Vacuum-resistant Fibers, refer to product information page.
>>Go to "One-Touch Connection System Vacuum-resistant Fibers"

Vacuum-resistant

■Thru-beam type (one pair set)

■Reflective type

Note:The sensing range of reflective type is the value for transparent glass 100 x 100 x t0.7 mm.

For details of Vacuum-resistant Fiber, refer to product information page.
>>Go to "Vacuum-resistant Fiber"

Metal-free

■Thru-beam type (one pair set)

Note:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

■Reflective type

Note 1:Note that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.

Note 2:The sensing range is specified for white non-glossy paper.

For details of Metal-free Fiber, refer to product information page.
>>Go to "Metal-free Fiber"

Cautions For Use

Using in combination with the FX-300 / FX-410 series

• The FX-100 series does not use the horizontal connectors that are used with the FX-300 / FX-410 series. Please note that horizontal connection cannot be performed using a connector attached cable. In addition, the optical communication function is not equipped on the FX-100 series, so it is unable to perform interference prevention for use with the FX-300 / FX-410 series.
  If using the FX-100 series together with the FX-300 / FX-410 series side-by-side, please set the same models together in groups.

Mounting

<When using a DIN rail>

How to mount the amplifier

[1]Fit the rear part of the mounting section of the amplifier on a 35 mm 1.378 in width DIN rail.

[2]Press down the rear part of the mounting section of the unit on the 35 mm 1.378 in width DIN rail and fit the front part of the mounting section to the DIN rail.

How to remove the amplifier

[1]Push the amplifier forward.

[2]Lift up the front part of the amplifier to remove it.

Note:Take care that if the front part is lifted without pushing the amplifier forward, the hook on the rear portion of the mounting section is likely to break.

<When using screws with washers>

• Use M3 screws with washers for mounting. The tightening torque should be 0.5 N·m or less.

Wiring

• Make sure that the power supply is OFF while adding or removing the amplifiers.
• Note that if a voltage exceeding the reted range is applied, or if an AC power supply is directly connected, the product may get burnt or damaged.
• Note that short-circuit of the load or wrong wiring may burn or damage the product.
• Do not run the wires together with high-voltage lines or power lines, or put them in the same raceway. This can cause malfunction due to induction.
• Verify that the supply voltage variation is within the rating.
• If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground.
• In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this product, connect the frame ground (F.G.) terminal of the equipment to an actual ground.
• Make sure to use the quick-connection cable (optional) for the connection of the controller.
  Extension up to total 100 m 328.084 ft is possible with 0.3 mm² or more, cable. However, in order to reduce noise, make the wiring as short as possible.

Part description

Setting mode

• Setting mode appears after the MODE key is pressed for 2 sec. in RUN mode.

PRO mode

• PRO mode appears after the MODE key is pressed for 4 sec. in RUN mode.

Setting item	Factory setting	Description
Shift setting	[Shift amount 15 %]	Shift amount can be selected from 0 to 80 % in the limit teaching. Select 0 % when it is desired to set the present incident light intensity as a threshold value.
External input setting	[Emission halt]	External input can be selected from emission halt, limit teaching [+], limit teaching [-], full-auto teaching, ECO (Note 1), 2-point teaching or emission amount test. When setting the incident light intensity test “”, output turns ON / OFF every 100ms when the rate of incident light intensity and threshold value is less than half of the set shift amount (for example, when the rate of incident light intensity and threshold value is within ±10 % for 20 % of shift amount) at external input.
Threshold value-storing setting mode (Note 2)		Threshold value set at the limit teaching, full-auto teaching or 2-point teaching by external input is stored. When selecting Auto in the emission amount setting mode, the set emission amount level is also stored.
Threshold value follow-up cycle setting (Note 3)		When incident light intensity exceeds threshold value, this mode can change the threshold value with each set cycle depending on variations of the incident light intensity. The follow-up shift amount is same as the one set in the shift setting mode. However, the threshold value is not stored.
GETA function setting (Note 4, 5)		Variations can be reduced by correcting the present incident light intensity in each amplifier to a target value. Target value to offset incident light intensity can be selected from 0 to 2,000 by 100 unit each. For example, if the target value is set to 2,000 when the incident light intensity is 1,500, the incident light intensity becomes 2,000.
ECO setting		It is possible to light up / turn off the digital display. When ECO setting mode is ON, the display turns off in 20 sec. approx. in RUN mode. To light up the display again, press any key for 2 sec. or more.
Digital display inversion setting		Digital display can be inverted.
Threshold value margin setting		Margin for threshold value to the present incident light intensity can be checked. When there is no margin, it is possible to make the digital display blink. : Set to “OFF”: does not function : Green blinks. : Red blinks. : Red and green blink. : When conducting limit teaching or 2-point teaching by external input, in case the rate of reference incident light intensity and threshold value after teaching is 200% or more, or in case it is less than half of the shift amount, output turns ON / OFF every 100 ms. (Note 6)
Setting copy		The settings of the master side amplifier can be copied to the slave side amplifier. For details, refer to “Setting copy function”.
Reset		Returns to default settings (factory settings.)

scroll

Setting copy function

Refer to the "Instruction Manual" for details.

Others

• This product has been developed / produced for industrial use only.
• Do not use during the initial transient time (0.5 sec.) after the power supply is switched on.
• Take care that the product is not directly exposed to fluorescent lamp from a rapid-starter lamp, a high frequency lighting device or sunlight etc., as it may affect the sensing performance.
• This product is suitable for indoor use only.
• Avoid dust, dirt, and steam.
• Take care that the product does not come in contact with oil, grease, organic solvents, such as thinner, etc., strong acid or alkaline.
• This product cannot be used in an environment containing inflammable or explosive gases.
• Never disassemble or modify this product.
• EEPROM is adopted to this product. It is not possible to conduct teaching 100 thousand times or more, because of the EEPROM’s lifetime.

Quick setting function

Note:Until production in November 2007, OFF or ON was selectable. The emission amount of Level 2 (ON) is about 40% of that of Level 3 (OFF).

Difference between previous model and upgraded one

• For upgraded ones (production in and after December 2007), “P” is marked near the beam-emitting inlet.
  Previous ones have no marking. Appearance and functions have been changed.

<After upgrade>

<Previous>

Code setting function