AUTOMATION
CONTROLS

Search
Discontinued
Products



LightPix AE10 (Discontinued Products)

Specifications

General Specifications

Item Specifications
Rated operation voltage 24V DC
Operating voltage range 21.6 to 26.4 V DC (including ripples)
Rated current consumption 0.5 A max.
Ambient temperature in use 0 to +40℃
Storage ambient temperature -20 to +60℃ (no freezing or condensation)
Ambient humidity
(in use and storage)
35 to 75%RH (no freezing or condensation)
Insulation resistance 100MΩ max. 500 V DC*
Breakdown voltage 500 V AC/1 min (600V AC/1 min.)*
Noise immunity 1000V (p-p), pulse width 50ns/1μs (using noise simulator method)
Weight Main unit: approx. 400g
Operation unit: approx. 200g
Finder unit: approx. 200g
Vibration resistance 10 to 55Hz, 1 cycle/1 min. Double amplitude of 1.5mm, 30min. each X,Y and Z directions
Shock resistance 196m/s2, 5 times each in X,Y and Z directions

*Evaluation was carried out with the primary side power supply varistor and capacitor removed from the internal circuit of the device.

Function Specifications

Main unit

Item Specifications
Model ANE101* ANE102* ANE103* ANE104*
Installation distance (mm) 45±2.5 105±5.5 50±5.0 120±12.0
Measurement range (mm) 10 x 8 25 x 20 50 x 40 100 x 80
Resolution (mm) 0.1 0.2 0.5
Photo acceptance unit Color, C-MOS
Valid pixels 352 Horizontal x 288 vertical pixels (100,000 pixels)
Image capture light source White LED
Exposure time Shutter timing and interlock
Input and Output Serial RS-485 port
  Transmission speed 9,600/14,400/19,200/38,400/57,600 bps
Transmission direction Half duplex
Synchronization system Asynchronous
Transmission code ASCII
Data length 8 bits
Parity check None
Stop bit length 1 bit
BCC Available
Delimiter CR (0DH)
Flow control No
Parallel Mini D-Sub, 15 pins (shared power supply)
  Input Photo coupler input, 6 points
Trigger: 1 bit; mode switch: 2 bits;
type switch: 3 bits
Output PhotoMOS output, 5 points
Ready: 1 bit; Alarm: 1 bit;
decision output: 3 bits
Dedicated device port Connection port for operation unit

Operation unit

Item Specifications
Display 7 segment, 3 colors
No. of switches 8
Dedicated device port Connection port for main unit
Content of input - Type switching (type 1 to 7)
- Mode switching (teaching/Run/Run-view)
- Trigger Input
- Permissible zone
- Device setting
(Transmission speed/device No./output delay/load delay/trigger switching/start-up type/function switching/backlight off time/auto saving/initialization/lamp on/off switching)
Display content - Judgement result
- Calculation result
- READY
- Alarm

Finder unit

Item Specifications
Display 2-inch color LCD
backlight White LED
Backlight life 40,000h (at 25℃)
Operation Available only with the operation unit

Application

ANE***0

Item Specifications
Part number ANE***0
Function name Color extraction
Color resolution 12 colors
(Use the Gretag Macbeth Color Rendition Chart for confirmation.)
Function (1) Colored area
(Detected area of registered color on object.)
(2) Color discrimination
(Distinguishes which color is closest to registered color.)
[These two modes switched in device setting mode. Simultaneous use is not possible.]
No. of registered items 7 types
Color registration method Teaching
Input value Upper and lower limit values for area judgement
Serial Input - Trigger input
- Type switching (types 1 to 7)
- Function switching
- Upper/lower limit values
- Save
Output - Judgement result
- Computation result (numerical)
- Error output
Parallel Input - Trigger input
- Type switching (Types 1 to 7)
- Mode switching (Teaching/Run/Run-view)
Output - Judgement result (OK/NG)
- READY
- Alarm

ANE***1

Item Specifications
Part number ANE***1
Function name Edge detection
Function (1) Edge detection
(2) Apex detection
[These two modes switched in device setting mode. Simultaneous use is not possible.]
No. of registered items 7 types
Object registration method Teaching
Input value Pemissible zone to determine edge position or apex coordinates.
Serial Input - Trigger input
- Type switching (types 1 to 7)
- Function switching
- Permissible values
- Save
Output - Decision result
- Computation result (numerical)
- Error output
Parallel Input - Trigger input
- Type switching (Types 1 to 7)
- Mode switching (Teaching/Run/Run-view)
Output - Judgement result (OK/NG)
- READY
- Alarm

ANE***2

Item Specifications
Part number ANE***2
Function name Width measurement
Function (1) Discriminates and judges max. and min.
vertical width, and max. and min. horizontal width.
No. of registered items 7 types
Object registration method Teaching
Input value Pemissible zone to determine max. and min. width.
Serial Input - Trigger input
- Type switching (types 1 to 7)
- Function switching
- Permissible values
- Save
Output - Decision result
- Computation result (numerical)
- Error output
Parallel Input - Trigger input
- Type switching (Types 1 to 7)
- Mode switching (Teaching/Run/Run-view)
Output - Decision result (OK/NG)
- READY
- Alarm

Return to top

CONTACT US
If you have any questions, please select the option below to contact us or find answers.
CONTACT BY EMAIL / PHONE FIND LOCAL OFFICE

Return to top

CONTACT US
BY EMAIL
Please click your area to select country or region




Requests to customers (Automation Control Components & Industrial Device) [Excluding specific product]
Requests to customers (Automation Control Components & Industrial Device) [For specific product]
Requests to customers (FA Sensors & Components [Excluding motors])
Requests to customers (Dedicated to industrial motors)