AUTOMATION
CONTROLS

Search
Discontinued
Products



39/20 mm Center Space Rotary Potentiometers

Specifications

Item Specifications
Mechanical Rotation Angle 300°
Rotation Torque
(Detents Torque)
15 mN・m to 50 mN・m
Electrical Nominal Total Resistance 10 kΩ (Tolerance ±20%)
Taper B
Power Rating 0.1 W
Residual Resistance 100 Ω max.
Insulation Resistance 50 MΩ min. (250 V DC)
Linearity ±3% max.
Dielectric Withstand Voltage 250 V AC for 1 minute
Noise Level 47 mV max.
Endurance Operating Life 30,000 cycles min.
Minimum Quantity/Packing Unit 50 pcs. (Tray Pack)
Quantity/Carton 250 pcs.

Return to top

Common Specifications

Electrical Specifications

1.Taper

Measuring Method Out-put Voltage
between Terminal 1 & 2
/ Operating Voltage
between Terminal 1 & 3
× 100(%)
Out-put Voltage
between Terminal 2 & 3
/ Operating Voltage
between Terminal 1 & 3
× 100(%)
Taper Effective Rotation Angle
EIAJ Panasonic 50% 50%*
15A A 10 to 25 -
1B B 40 to 60 -
15C C - 10 to 25
10A D 6 to 15 -
4B G 40 to 60 -
H BH Linear taper

Notes:

1.* Angle from terminal 3 side.
2.( ) is per JIS (Japanese Industrial Standard). Unless otherwise specified, we consider it at 50 % rotation, however, upon request above JIS can be applied.
3.[ ] is only reference value.

Standard Taper

Standard Taper

2.Tracking

The tracking should be calculated as follows.

Tracking (dB) = 20 log (VR2 / VR1)

Where:
VR1 = Voltage between terminal 1 & 2 of section R1
VR2 = Voltage between terminal 1 & 2 of section R2

Test voltage between terminal 1 & 3 shall be 2 V to 5 V (1000±200 Hz).

In case of a potentiometer with a tap, the measurement should be made by connecting a fixed resistor between tap terminal and terminal 1. Unless otherwise specified, tolerance of the fixed resistor shall be ±10%. If your requirements different, inform us of your specifications.

Mechanical Specifications

1.Shaft Angle

Shaft angle against mounting surface shall be 90°. Shaft bend and shaft wobble shall be a × L/30 (mm) max. when 50 mN·m moment applied to the measuring point of shaft.

Where:
a = Constant Value as shown below
L = Distance between mounting surface and measuring point on the shaft

Size Shaft material Shape & Type Shaft wobble (a) Bending moment
14 mm square
18 mm square
(Common)
Metal shaft Without switch 1-shaft type 0.3 mm 50 mN・m
With push switch 0.5 mm
Insulated shaft With bushing Single 0.5 mm
Snap-in 0.7 mm

2.Nut Tightening Torque

When nut is tightened as specified below, unevenness of shaft rotation shall not occur.

Bushing Dia., etc. Tightening Strength
M7 to M9 1.0 N・M

Return to top

CONTACT US
If you have any questions, please select the option below to contact us or find answers.
CONTACT BY EMAIL / PHONE FIND LOCAL OFFICE SEARCH FAQ

Return to top

CONTACT US
BY EMAIL
Please click your area to select country or region







BY PHONE

FAQ

Related Information
FA Sensors & Components

Requests to customers (Automation Control Components & Industrial Device) [Excluding specific product]
Requests to customers (Automation Control Components & Industrial Device) [For specific product]
Requests to customers (FA Sensors & Components [Excluding motors])
Requests to customers (Dedicated to industrial motors)