Business > Industrial Devices > Automation Controls Top > Components & Devices > Switches > Seal Type Switches > Turquoise Stroke Mini Switch Resistor installed type > Rating/Performance

Turquoise Stroke Mini Switch Resistor installed type

Lineup
- ABJ (BJ) Turquoise Switches Ultra-miniature Size Sealed Switches
- ABS (BS) Turquoise Switches Subminiature Size Sealed Switches
- ABV (BV) Turquoise Switches Miniature Size Sealed Switches
- Turquoise Stroke Switches Long Stroke and Sliding Contact Construction Sealed Switches
- Turquoise Stroke Mini Switches Small size and Long Stroke Sliding Contact Construction Sealed Switches
- Turquoise Stroke Mini Switch Resistor installed type Small seal switches with wiring failure detecting function
CAD data　 Catalogs/Datasheets　　
FAQ

Rating/Performance

Rated

Please use within the range below.

1) Rated power	:	Environment temperature -40°C ≦ T ≦ 70°C 0.50 W
		Environment temperature 70°C < T ≦ 75°C 0.45 W
		Environment temperature 75°C < T ≦ 85°C 0.40 W
2) Voltage	:	4.5 to 16 V DC
3) Minimum current	:	1 mA

Return to top

Operation environment and conditions

Item	Specifications
Ambient and storage temperature	–40°C to +85°C (no freezing and condensing)
Allowable operating speed	30 to 500 mm/sec.
Max. operating cycle rate	120 cpm

*	When switching at low and high speeds or under vibration, or in high-temperature, high-humidity environments, life and performance may be reduced significantly depending on the load capacity. Please consult us.

Return to top

Electrical characteristics

Item

Specifications

Circuit diagram

Output resistance
(Initial)

FP : 510 Ω		±1.5％ (20 to 30°C)
		±2.5％ (-40 to +85°C)
TTP : 1,510 Ω		±1.5％ (20 to 30°C)
		±2.5％ (-40 to +85°C)

FP : 1,510 Ω		±1.5％ (20 to 30°C)
		±2.5％ (-40 to +85°C)
TTP : 510 Ω		±1.5％ (20 to 30°C)
		±2.5％ (-40 to +85°C)

Return to top

Characteristics

Item		Specifications
Electrical switching life	DC 4.5 to 5.5 V	Min. 3 × 10⁵	Switching frequency: 20 times/min Plunger operation speed: 100 mm/s Plunger switching position: Free Position (FP) to Total Travel Position (TTP)
Electrical switching life	DC 8 to 16 V	Min. 2 × 10⁵
Vibration resistance (malfunction vibration resistance)		Single amplitude: 0.75 mm Amplitude of vibration: 10 to 55 Hz (4 minutes cycle) Direction and time: 30 minutes each in X, Y and Z directions
Vibration resistance (malfunction vibration resistance)		Amplitude of vibration: 5 to 200 Hz (10 minutes cycle) Acceleration: 43.1 m/s² Direction and time: 30 minutes each in X, Y and Z directions
Shock resistance (malfunction shock resistance)		Shock value: 980 m/s² Direction and time: 5 times each in X, Y and Z directions
Terminal strength		Min. 6 N (each direction) *Terminal deformation possible.
Heat resistance		85°C 500 hours
Cold resistance		–40°C 500 hours
Humidity resistance		40°C 95% RH 500 hours
Unit weight		Approx. 0.5 g (Terminal type), Approx. 4.1 g (Wire leads type)
Protection grade		IP67 (except exposed terminal part of terminal type)

Notes: As long as there are no particular designations, the following conditions apply to the test environment.
• Ambient temperature: 5 to 35°C
• Relative humidity: 25 to 85% RH
• Air pressure: 86 to 106 kPa

Return to top

Protection grade

1)IEC 60529 (rating for outer shell protection):
IP67 (Immersion protected) except metal terminal part (See below drawing) (Note 1)

2)JIS D0203 (method for testing moisture resistance and water resistance in automotive components) Equivalent of D2 (Note 2)

Note 1)	A concrete testing method is to check for any adverse effect on the structure after leaving it submerged for 30 minutes under 1 m of water (with temperature difference between water and switch no larger than 5°C).
Note 2)	A concrete testing method is to check for any adverse effect on the structure after leaving it submerged for 10 minutes under 10 cm water (with temperature difference between water and switch no larger than 30°C).

Return to top

Operating characteristics

Characteristics		Pin plunger	Simulated roller lever
Operating Force (OF) Max.		1.2 N	1.5 N
Total Travel Force (TF) Max. reference value		(3.0 N)	(2.8 N)
Free Position (FP) Max.	Terminal type	7.7 mm	13.4 mm
Free Position (FP) Max.	Wire leads type	14.45 mm	20.15 mm
Operating Position (OP)	Terminal type	Initial: 7.1±0.25 mm After test: 7.1±0.3 mm	Initial: 10.75±0.6 mm After test: 10.75±0.7 mm
Operating Position (OP)	Wire leads type	Initial: 13.75±0.35 mm After test: 13.75±0.4 mm	Initial: 17.4±0.7 mm After test: 17.4±0.8 mm
Release Position (RP)	Terminal type	Initial: 7.15±0.3 mm After test: 7.15±0.35 mm	Initial: 11.05±0.7 mm After test: 11.05±0.8 mm
Release Position (RP)	Wire leads type	Initial: 13.8±0.4 mm After test: 13.8±0.45 mm	Initial: 17.7±0.8 mm After test: 17.7±0.9mm
Over Travel (OT) Min.	Terminal type	Initial: 1.75 mm After test: 1.70 mm	Initial: 2.25 mm After test: 2.15 mm
Over Travel (OT) Min.	Wire leads type	Initial: 1.65 mm After test: 1.60 mm	Initial: 2.15 mm After test: 2.05 mm
Total Travel Position (TTP) Reference value	Terminal type	(5.1 mm)	(7.9 mm)
Total Travel Position (TTP) Reference value	Wire leads type	(11.75 mm)	(14.55 mm)