Integrated Display Type Digital Flow Sensor FM-200 (Discontinued Products)

Notes:

Terminal arrangement of the connectors of this product (sensor body)

• This product can be installed facing up or down or to the left or right.

• Use M3 screws, and the tightening torque should be 0.5 N·m.

<Resin body type>

Vertical mounting

• Use M3 screws, and the tightening torque should be 0.5 N·m.

<Resin body type>

<Aluminum body type>

When using sensor mounting bracket

• When mounting the product on the sensor mounting bracket MS-FM2-1 (optional) or MS-FM2-2 (optional), use the M3 screws (length 6 mm 0.236 in) attached to the sensor mounting bracket. The tightening torque should be 0.5 N·m. Use M3 screws to mount the sensor mounting bracket on a sensing surface.

<Resin body type> Use 　MS-FM2-1

<Aluminum body type> 　Use MS-FM2-2

• The following specified tube should be used to insert to the push-in joint type product.

• Before using this product, make sure to check that the tube is firmly inserted.
• Install a filter, an air dryer and an oil mist filter (micro-alescer) onto the primary side (upstream) of this product since the compressed air from the compressor contains drain (water, oil oxide and foreign materials, etc.). Mesh (wire net) in this product is used to rectify the flow rate in the pipe. Always install a filter to the primary side of this product since this mesh is not a filter to remove foreign materials.

• When using a valve on the primary side of the product, only use an oil-prohibit specification valve. This product may malfunction or break if subject to splattering grease or oil, etc.
• When using this product for suction verification, etc., always install an air filter whose filtration property is 10 μm 0.394 mil or less onto the suction side to prevent suction of foreign materials and water. Furthermore, consider atmospheric dew point and ambient temperature of the product, use the product under the conditions that dew condensations will not be formed in the inside of pipe.
• In case of mounting commercial joint to the aluminum body type, apply a spanner on the metal part of this product and tighten by the tightening torque of 16 to 18 N·m. If excessive torque is applied, the commercial joint or the main body may break.
• When piping, take care that foreign materials such as sealing tape and adhesive must not enter into the inside of the pipe. If foreign materials are entered, the product may malfunction or break.
• Make sure to mount the joint when using the product with its secondary side (downstream) open to the air. If the joint is not mounted, the port filter of the product may fall off.

• Make sure that the power supply is OFF during wiring.
• Take care that wrong wiring will damage this product.
• Take care if applying voltage exceeding the rated range, or connecting to AC power supply, this product may break or burn.
• If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground.
• In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this sensor, connect the frame ground (F.G.) terminal of the equipment to an actual ground.
• Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This can cause malfunction due to induction.
• Extension up to total 10 m 32.808 ft is possible with 0.3 mm², or more, cable.
• Make sure that stress by forcible bend or pulling is not applied directly to the sensor cable joint.

• Take care if foreign materials are mixed in the sensing part, the product may break.
• Do not use this product for commercial purposes since the product does not comply with International System of Units (SI).
• Do not apply pressure that exceed resistant-pressure.
• Do not use during the initial transient time (approx. 5 sec.) after the power supply is switched ON.
• The specifications may not be satisfied in a strong magnetic field.
• Accuracy of the display and the analog voltage output is influenced by self-heating by applying current other than the temperature characteristics. Standby time (5 min. or more after applying current) should be taken when using the product.
• These sensors are only for indoor use.
• Do not use this product in places having excessive vapor, dust, etc., or where it may come in contact with corrosive gas, etc.
• Take care that the product does not come in contact with water, oil, grease, or organic solvents such as thinner, etc., strong acid or alkaline.
• Do not drop the product or apply hard shock. This can cause product breakage.