【Notification of Manufacturer Change for Panasonic Industrial Devices SUNX Products and Panasonic Industrial Devices SUNX Tatsuno Products】
From April 1, 2024, the terms "Panasonic Industrial Devices SUNX Co., Ltd." and "Panasonic Industrial Devices SUNX Tatsuno Co., Ltd."
in this page and in the manuals and other documents to be downloaded will all be replaced with "Panasonic Industry Co., Ltd." and applied accordingly.

Business > Industrial Devices > Automation Controls Top > FA Sensors & Components > Sensors > Fiber Sensors > Digital Fiber Sensor FX-550L > Specifications

Digital Fiber Sensor FX-550L

Specifications

Specifications

Type		Discrete wire type	M12 connector type
Model No.		FX-551L3-P-C2	FX-551L3-P-J
Applicable regulations and certifications		CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations)
Supply voltage		12 to 24 V DC ⁺¹⁰₋₁₅ % Ripple P-P 10 % or less
Power consumption		Normal operation: 960 mW or less (current consumption 40 mA or less at 24 V supply voltage) ECO mode: 720 mW or less (current consumption 30 mA or less at 24 V supply voltage)
Communication output (C/Q) (Note 2)	IO-Link communication	IO-Link Specification V1.1
	Baud rate	COM3(230.4kbps)
	Process data	4byte
	Minimum cycle time	1.0ms
Control output (DO)		PNP open-collector transistor • Maximum source current: 50 mA • Applied voltage: 30 V DC or less (between output and +V) • Residual voltage: 2 V or less (Note 3) (at maximum source current)
	Output operation	Switchable either Light-ON or Dark-ON by L/D mode
	Short-circuit protection	Incorporated
Response time		STD: 250 μs or less, LONG: 2 ms or less, U-LG: 4 ms or less, HYPR: 24 ms or less, selectable
Sensitivity setting		2-point teaching / Limit teaching / Full-auto teaching / Manual adjustment
Incident light sensitivity setting		Incorporated, 4 steps
Incident light intensity display range		STD: 0 to 4,000, LONG: 0 to 8,000, U-LG / HYPR: 0 to 9,999
Timer function		Incorporated with variable OFF-delay / ON-delay / One-shot, switchable either effective or ineffective
	Timer period	0.1 to 999.9 ms approx., in units of 0.1 ms approx.
Different frequency interference prevention function (Note 4)		Incorporated (up to 4 units). Note that the response time varies depending on the setting. F-1: 0.8 ms or less, F-2: 0.9 ms or less, F-3: 1.0 ms or less, F-4: 1.7 ms or less
Protection		IP40(IEC)
Ambient temperature		-10 to +55℃ +14 to +131℉ (If 4 to 7 units are mounted in cascade: -10 to +50℃ +14 to +122℉ or if 8 to 16 units are mounted in cascade: -10 to +45℃ +14 to +113℉) (No dew condensation or icing allowed), Storage: -20 to +70℃ -4 to +158℉
Vibration resistance		10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude (10 G max.) in X, Y and Z directions for two hours each
Shock resistance		98 m/s² acceleration (10 G approx.) in X, Y and Z directions five times each
Emitting element (modulated)		Red LED (Peak emission wavelength: 660 nm 0.026 mil)
Material		Enclosure, Case cover: Polycarbonate, Switch: Polyacetal
Cable		0.2 mm² 4-core cabtyre cable, 2 m 6.562 ft long	0.2 mm² cabtyre cable with M12 connector, 0.3 m 0.984 ft long
Cable extension		Extension up to total 20 m 65.617 ft is possible with 0.3 mm², or more, cable. (Condition of CE compliance: less tan 20 m 65.617 ft) (however, supply voltage 12 V DC or more)
Weight		Net weight: 55 g approx., Gross weight: 80 g approx.	Net weight: 35 g approx., Gross weight: 60 g approx.

Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23℃ +73.4℉.

2) When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).

3) In case of using the cable (cable length 2 m 6.562 ft).

4) This function increases the hysteresis. Check the sensing condition when using the function.

Notes: 1)	Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23℃ +73.4℉.
2)	When the sensor is used as an ordinary sensor, the communication output (C/Q) provides the same output operation as the control output (DO).
3)	In case of using the cable (cable length 2 m 6.562 ft).
4)	This function increases the hysteresis. Check the sensing condition when using the function.