Business
> Industrial Devices
> Automation Controls Top
> FA Sensors & Components
> Measurement Sensors
> Measurement Sensors
> Compact Laser Displacement Sensor HL-G1
> Part Number
> HL-G108A-RS-J
HL-G108A-RS-J | Compact Laser Displacement Sensor HL-G1
|
*Photo may vary from actual product.
This product has been confirmed that it does not contain the 6 substances specified in EU RoHS Directive 2011/65/EU and the 4 substances specified in 2015/863/EU.
| Product Number | HL-G108A-RS-J |
| Part Number | HL-G108A-RS-J |
| Product | Compact Laser Displacement Sensor |
| Details | Sensor head (High functionality type) |
| Product name | Compact Laser Displacement Sensor HL-G1 |
As of April 17, 2024
Specifications and design of the products are subject to change without notice for the product improvement.
Spec Detail
| Item | Specifications |
|---|---|
| Product Number | HL-G108A-RS-J |
| Part Number | HL-G108A-RS-J |
| Regulatory compliance | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) |
| Type | High functionality type |
| Measurement center distance | 82.9 mm 3.264 in |
| Measuring range | ±10 mm ±0.394 in |
| Resolution | 2.5 μm 0.098 mil |
| Linearity | ±0.2 % F.S. |
| Temprerature characteristics | ± 0.08 % F.S. / ℃ |
| Light source | Red semiconductor laser, Class 1 (IEC / EN / JIS / GB / KS / FDA (Note：This product complies with the FDA regulations (FDA 21 CFR 1040.10 and 1040.11) in accordance with FDA Laser Notice No. 56, except for complying with IEC 60825-1 Ed. 3. Max. output: 0.39 mW (Peak emission wavelength: 655 nm 0.026 mil) |
| Beam diameter | 0.2 × 0.2 mm 0.008 × 0.008 in (Note) This beam diameter is the size at the measurement center distance. These values were defined by using 1/e2 (13.5 %) of the center light intensity. If there is a slight leakage of light outside the normal spot diameter and if the periphery surrounding the sensing point has a higher reflectivity than the sensing point itself, then the results may be affected. |
| Receiving element | CMOS image sensor |
| Supply voltage | 24 V DC ± 10 % including ripple 0.5 V (P-P) |
| Current consumption | 100 mA or less |
| Sampling rate | 200 μs, 500 μs, 1 ms, 2 ms |
| Analog output : Voltage | Output range: 0 to +10.5 V (normal), 11 V (alarm) Output impedance: 100 Ohm |
| Analog output : Current | Output range: 3.2 to 20.8 mA (normal), 21.6 mA (alarm) Load impedance: 300 Ohm or less |
| Outputs (OUT 1, OUT 2, OUT 3) | Judgment output or alarm output (Setting can be selected.) Selectable NPN transistor open-collector or PNP transistor open-collector -Maximum sink current: 50 mA -Applied voltage: 3 to 24 V DC (between output and 0 V) -Residual voltage: 2 V or less (at 50 mA of sink current) -Maximum source current: 50 mA -Residual voltage: 2.8 V or less (at 50 mA of source current) |
| Output (OUT 1, OUT 2, OUT 3) : Output operation | Opened when the amount of light is insufficient. |
| Output (OUT 1, OUT 2, OUT 3) : Short circuit protection | Incorporated (automatic restoration) |
| Output polarity setting input | NPN open collector output operates when 0 V is connected. PNP open collector output operates when 24 V DC is connected. |
| Timing input | NPN output operates when 0V is connected and NPN is set. (It depends on the setting.) PNP output operates when external power + is connected and PNP is set. (It depends on the setting.) |
| Multi input | Zero set, zero set off, reset, memory switching, teaching, saving, and laser control according to the input time. In case NPN output is selected, Function varies according to the time 0 V is connected NPN. In case PNP output is selected, Function varies according to the time external power + is connected. |
| Communications interface | RS-422 or RS-485 (selectable) Baud rate: 9,600/19,200/38,400/115,200/230,400/460,800/921,600 bps Data length 8 bit, Stop bit length 1 bit, Without parity check, BCC check, Termination code: CR |
| Indicator : Laser emission | Green LED (lights up during laser emission) |
| Indicator : Alarm | Orange LED lights up when this product cannot measure because of insuffienct or excessive light intensity. |
| Indicator : Measurement range | Three yellow LED |
| Digital display | Red LED 5 digit display |
| Degree of pollution | 2 |
| Operating altitude | 2,000 m 6561 ft or less |
| Environmental resistance : Protection | IP67 |
| Environmental resistance : Ambient temperature | -10 to +45 ℃ +14 to +113 ℉ (No dew condensation allowed), Storage: -20 to +60 ℃ -4 to +140 ℉ |
| Environmental resistance : Ambient humidity | 35 to 85 % RH, Storage: 35 to 85 % RH |
| Environmental resistance : Ambient illuminance | Incandescent light: 3,000 liter x or less at the light-receiving face (Note) The fluctuation by ambient illuminance is ± 0.1 % F.S. or less. |
| Insulation resistance | 20 MOhm , or more, with 250 V DC between all supply teminals connected together and enclosure |
| Voltage withstandability | 1,000 V AC for one min. between all supply terminals connected together and enclosure |
| Environmental resistance : Vibration resistance | 10 to 55 Hz (period: 1 min.) frequency, 1.5 mm 0.059 in double amplitude in X,Y and Z directions for two hours each |
| Environmental resistance : Shock resistance | 500 m/s2 acceleration (50 G approx.) in X,Y and Z directions three times each |
| Material | Enclosure: PBT Front cover: Acrylic Cable: PVC |
| Cable | 14-core cabtyre cable with connector, 0.5 m 1.640 ft long |
| Cable extension | Extension up to total 20 m 65.617 ft is possible with optional cable (Cable for standard type cannot be extended) . |
| Weight | Net weight: 70 g approx. (not including cable), 110 g approx. (including cable) Gross weight: 160 g approx. |
| Accessory | Warning label: 1 set |
| Remark | Where measurement conditions have not been specified precisely, the conditions used were as follows: supply voltage 24 V DC, ambient temperature +20 ℃ +68 ℉, sampling rate 500 μs, average number of samples: 1024, measurement center distance, object measured is made of white ceramic (specular reflection type: an aluminum vapor deposition surface reflection mirror) and analog measurement values. |
Accessories (Option)
|
| Product Number | HL-G1CCJ10 |
| Part Number | HL-G1CCJ10 |
| Product name | Extension Cable |
|
|
| Product Number | HL-G1CCJ2 |
| Part Number | HL-G1CCJ2 |
| Product name | Extension Cable |
|
|
| Product Number | HL-G1CCJ20 |
| Part Number | HL-G1CCJ20 |
| Product name | Extension Cable |
CONTACT US
If you have any questions, please select the option below to contact us or find answers.
CONTACT US
BY EMAIL
BY EMAIL
Please click your area to select country or region
BY PHONE
- U.S.A.
- +1-800-344-2112
- Europe
- +49-89-45354-1000
- China
- +86-10-59255988
- Singapore
- +65-6299-9181
Requests to customers (Automation Control Components & Industrial Device) [Excluding specific product]
Requests to customers (Automation Control Components & Industrial Device) [For specific product]
Requests to customers (FA Sensors & Components [Excluding motors])
Requests to customers (Dedicated to industrial motors)
- COMPONENTS & DEVICES
- FA SENSORS & COMPONENTS
- Fiber Sensors
- Photoelectric Sensors / Laser Sensors
- Micro Photoelectric Sensors
- Light Curtains / Safety Components
- Area Sensors
- Inductive Proximity Sensors
- Particular Use Sensors
- Sensor Options
- Wire-Saving Systems
- Programmable Controllers / Interface Terminal
- Human Machine Interface
- Pressure Sensors / Flow Sensors
- Measurement Sensors
- Static Control Devices
- Laser Markers / 2D Code Readers
- Machine Vision System
- Energy Management Solutions
- Timers / Counters / FA Components
- MOTORS
