GT707 / GT703 / GT704 Firmware Version-Up Information

Version-up Information

Version-Up information for GT703(Ver.1.46) / GT704(Ver.1.46) / GT707(Ver.1.65) (January 9, 2024 Update)

The following points have been upgraded.

  • Corrected the phenomenon that a communication error occurs when communication between GT and external device overlaps when using general-purpose serial (two-way communication mode 2) with RS422 model. (GT703/GT704)
  • Corrected the phenomenon that when using general-purpose serial (two-way communication mode 2) with an RS422 model, a communication error may occur if transmission to an external device is repeated by repeatedly pressing a switch, etc. (GT703/GT704)
  • Corrected the phenomenon where the GT would freeze when writing a large recipe file.
  • Corrected the phenomenon where if the power is turned on again after deleting a recipe block, blocks after the deleted block cannot be referenced.
  • Corrected the phenomenon where recipe data could not be created up to the maximum recipe data size.
  • Corrected the phenomenon where an error notification was not issued even if the file capacity exceeded when adding a recipe block.
  • Corrected the phenomenon where the recipe file may be written to exceed the actual file size when deleting recipe data.
  • Corrected the phenomenon that SD → GT copy function does not work with SD card in LOCK state.

Version-Up Information for GT703(Ver.1.45) / GT704(Ver.1.45) / GT707(Ver.1.64) (March 22, 2021 Update)

The following points have been upgraded.

  • Supports 180 degree rotation function. (GT707)
  • Supports BAT LOW flag. (GT703 / GT704)
  • Corrected the phenomenon that the graph display may shift when "blink" is set for line graph parts (Block).
  • Corrected the phenomenon that the graph may not be displayed when the "Total Value" is set for the line graph part (Block).
  • Corrected the phenomenon that may not be displayed correctly when the "Total Value" is set for the line graph part (Block).
  • Corrected the phenomenon that the graph display may not be maximized when "Automatic Setting" in "Max./Min." is set to "Yes" in the line graph parts (Block).
  • Corrected the phenomenon that the GT device cannot be monitored by the FP monitor function. (GT703 / GT704)
  • Corrected the phenomenon that the "Add" button on the second and subsequent lines does not switch when switching languages on the FP monitor registration monitor screen. (GT704)
  • Corrected the phenomenon that the display format change switch disappears when the "RUN" switch is pressed on the continuous monitor screen of GT704 (Portrait). (GT704)
  • Corrected the phenomenon that the device value is not displayed correctly on "Entry monitor" screen of GT707 (Portrait). (GT707)
  • Corrected the phenomenon that a timeout error may occur during PLC backup from FPXH. (GT707)
  • Corrected the phenomenon that the screen 0 may return and the parts may blink when the ASCII data logging trigger occurs.
  • Corrected the phenomenon that the holded data may be corrupted if the power is turned off / on after changing the GR area by bit operation when the "Hold GT Device" setting is set.
  • Corrected the phenomenon that the display may be distorted during the "Reversed When Pressed" operation of the transparent custom switch.
  • Corrected the phenomenon that the FP0H program created with FPWIN Pro7 cannot be uploaded and downloaded.
  • Corrected the phenomenon that general-purpose serial commands with short transmission intervals may not be processed.

Version-Up Information for GT703(Ver.1.44) / GT704(Ver.1.44) / GT707(Ver.1.63) (August 5, 2019 Update)

The following points have been upgraded.

  • Corrected the phenomenon that a communication error may occur when communicating to FP7 with the through function.

Version-Up Information for GT703(Ver.1.43) / GT704(Ver.1.43) / GT707(Ver.1.62) (February 21, 2019 Update)

The following points have been upgraded.

  • Improve to make GT link starts at high speed.
  • Corrected the phenomenon that error "ER0061" may occur when input of data parts is decided.
  • Corrected the phenomenon that the GT link error may occur when communication is normal.
  • Corrected the phenomenon that the upload from GT may fail.
  • Corrected the phenomenon that sometimes it operates as "Off" even if setting the CS/RS Control of the GT Configuration setting to "On".
  • Corrected the phenomenon that may not light up when returning from the backlight blinking state to lighting ".
  • Corrected the phenomenon that may freeze if 256 device writes are registered.
  • Corrected the phenomenon that the error display was not cleared even if the GT link token was received normally.

Version-Up Information for GT703(Ver.1.42) / GT704(Ver.1.42) (August 22, 2018 Update)

The following points have been upgraded.

  • Corrected the phenomenon that login might not be possible due to ID / Password of FTP server function set by GTWIN.

Version-Up Information for GT703(Ver.1.41) / GT704(Ver.1.41) / GT707(Ver.1.61) (July 19, 2018 Update)

The following points have been upgraded.

  • Corrected the phenomenon that may jumps to the screen 0 when jumping to the keyboard screen.
  • Corrected the phenomenon that wrong error code is displayed when an error occurs in SD Recipe writing.
  • Corrected the phenomenon that parts on the screen may not be displayed when the PLC model is "Modbus (RTU mode)".
  • Corrected the phenomenon that entered characters may not be displayed correctly when entering Japanese kana characters on the keyboard screen.
  • Corrected the phenomenon that the position of the input Data Parts in the keyboard screen may be shifted when using GT with Portrait.
  • Corrected the phenomenon that may not be logged even if the logging trigger condition is met. (GT703/GT704)

Version-Up Information for GT703(Ver.1.400) / GT704(Ver.1.400) / GT707(Ver.1.600) (February 1, 2018 Update)

The following points have been upgraded.

  • Added the FTP server function. (GT703/GT704)
  • Supports connecting to Mitsubishi MELSEC Q/L series via Ethernet port. (GT703/GT704)
  • Supports connecting by Modbus-TCP protocol via Ethernet port. (GT703/GT704)
  • Corrected the phenomenon that rebooting when displaying the system menu screen if Allen-Bradley SLC 500 MicroLogix series is set for PLC model.
  • Corrected the phenomenon that the FPWIN-GR7 may not upload in through mode during connection with Panasonic FP7 series.
  • Corrected the phenomenon that only 2 digits may be saved in the log file when logging more than 3 digits with ASCII.
  • Corrected the phenomenon that the alarm message becomes default string when saving alarm history to the SD card.
  • Corrected the phenomenon that the data parts may disappear when setting the value of 80H(128) or more to the first word of the data parts of ASCII (FP7 format).
  • Corrected the phenomenon that the year value output by the transfer outside function of the clock may become abnormal value.
  • Corrected the phenomenon that the notification command of SD card saving completion may be sent when the alarm history overflows in case of general purpose serial.
  • Corrected the phenomenon that hight light spots may be displayed on the screen.
  • Corrected a phenomenon that lines other than deleted alarms may be blank when one alarm is deleted on the alarm history part.

Version-Up Information for GT707(Ver.1.510) (October 16, 2017 Update)

The following points have been upgraded.

  • Corrected the error that the number of digits of ASCII data saved by logging function is abnormal.
  • Corrected the error that the message is default (Alarm0) when saving alarm history to SD card.
  • Corrected the error that the year data may become abnormal value when GT clock is transfer to the outside.

Version-Up Information for GT707(Ver.1.500) (July 18, 2017 Update)

The following points have been upgraded.

  • Added the variable file (FPWIN Pro) import function.
  • Corrected phenomenon that the file name may not displayed in the block file list of the SD recipe.
  • Corrected the phenomenon that "**0004" error may displayed and freeze, when the PLC model is General-Purpose serial.

Return to top

 

Return to top