[System Maintenance Notice]
Due to ongoing system maintenance, the site search and specification search functions are temporarily unavailable. We apologize for any inconvenience this may cause and appreciate your understanding.
【Notification of Manufacturer Change for Panasonic Industrial Devices SUNX Products and Panasonic Industrial Devices SUNX Tatsuno Products】
From April 1, 2024, the terms "Panasonic Industrial Devices SUNX Co., Ltd." and "Panasonic Industrial Devices SUNX Tatsuno Co., Ltd."
in this page and in the manuals and other documents to be downloaded will all be replaced with "Panasonic Industry Co., Ltd." and applied accordingly.
Business > Industrial Devices > Automation Controls Top > FA Sensors & Components > Sensors > Light Curtains / Safety Components > Safety door switch with key SG-B2 > Dimensions
Door switch
|
|
Notes:
1) | Plug the unused actuator entry slot using the plug supplied with the switch. |
---|---|
2) | When mounting the safety switch, be sure to conform to the mounting hole dimensions and secure in place with four screws. |
Door switch (rear unlocking button type)
|
As shown in the figure on the right, the mounting reference position of the actuator when inserted in the safety switch is: |
Straight actuator
|
Right-angle actuator (SG-K22)
|
Straight actuator with rubber bushings
Note:The actuator stop is used to adjust the actuator position. Remove the actuator stop after the actuator position is mounted.
* | Mounting pitch is set to 12 mm 0.472 in in factory. When setting the mounting pitch to 20 mm 0.787 in, widen the pitch of rubber cushions to 20 mm 0.787 in. |
---|---|
* | The actuator has movement flexibility to the directions shown in (B). |
Right-angle actuator with rubber bushings
Note:The actuator stop is used to adjust the actuator position. Remove the actuator stop after the actuator position is mounted.
* | When the mounting pitch is 12 mm 0.472 in (factory setting), the actuator has movement flexibility to the directions shown in (A) and (B). |
---|---|
* | When the mounting pitch is 20 mm 0.787 in, the actuator has movement flexibility to the directions shown in (B). Side the rubber cushions together with the screws. |
Slide actuator
Horizontal / Vertical angle adjustable actuators
|
The orientation of adjustment of angle adjustable (vertical / horizontal) actuators is determined by the position in which the orienting insert (white plastic) is installed on the back of the actuator.
Install the insert according to the desired orientation of adjustment.
Exercise care not to lose the orienting insert. The actuator will not operate properly without the orienting insert.
Padlock hasp (Optional)
Mounting plate (Optional)
|
Rear unlocking button kit for a frame (Optional)
|
|
Example: | When mounted on a □30 mm □1.181 in frame using the mounting plate above MS-SG-21, select MS-SG-22 since the mounting part thickness (X) is 40 (X = 10 + 30 = 40) 1.575 (X = 0.394 + 1.181 = 1.575). For more information about selecting a back manual unlocking button kit for a frame, see the following table: |
---|
Model No. | Mounting part* thickness (X) (mm in) |
---|---|
Rear unlocking button type When installing an SG-B2-K2□D-L5 with a rear unlocking button directly |
|
MS-SG-22 | 33 < X ≤ 43 1.299 < X ≤ 1.693 |
MS-SG-23 | 23 < X ≤ 33 0.906 < X ≤ 1.299 |
* The mounting part is a frame or a panel that the product is mounted on.
Requests to customers (Automation Control Components & Industrial Device) [Excluding specific product]
Requests to customers (Automation Control Components & Industrial Device) [For specific product]
Requests to customers (FA Sensors & Components [Excluding motors])
Requests to customers (Dedicated to industrial motors)