AUTOMATION
CONTROLS

Search
Discontinued
Products



Digital Fiber Sensor FX-500 Ver.2

Specifications

Type Standard type 2-output type Cable type
(Analog output type)
Model
No.
NPN output FX-501 FX-502 FX-505-C2
PNP output FX-501P FX-502P FX-505P-C2
Regulatory compliance EMC Directive, RoHS Directive, UL/c-UL Listing certification, Korean S mark certification
Supply voltage 12 to 24 V DC+10-15 % Ripple P-P 10 % or less
Power consumption Normal operation: 960 mW or less (current consumption 40 mA or less at 24 V supply voltage, excluding analog output of cable type)
ECO mode: 680 mW or less (current consumption 28 mA or less at 24 V supply voltage, excluding analog output of cable type)
Output
(2-output type and cable type:
Output 1, Output 2)
<NPN output type>
NPN open-collector transistor
• Maximum sink current: 100 mA (2-output type and cable type are 50 mA) (Note 2)
• Applied voltage: 30 V DC or less (between output and 0 V)
• Residual voltage: 2 V or less (Note 3) (at maximum sink current)

<PNP output type>
PNP open-collector transistor
• Maximum source current: 100 mA (2-output type and cable type are 50 mA) (Note 2)
• Applied voltage: 30 V DC or less (between output and +V)
• Residual voltage: 2 V or less (Note 3) (at maximum source current)
  Output points 1 point 2 points
Output operation Switchable either Light-ON or Dark-ON by L/D mode
Short-circuit protection Incorporated
Response time H-SP: 25 μs or less, FAST: 60 μs or less, STD: 250 μs or less, LONG: 2 ms or less, U-LG: 4 ms or less, HYPR: 24 ms or less, selectable
Analog output
(Cable type only)
Output current: 4 to 20 mA approx. [H-SP, FAST STD: At 0 to 4,000 digits, LONG: At 0 to 8,000 digits (Note 4)], Response time: 2 ms or less, Zero point: Within 4 mA ±1 % F.S., Span: Within 16 mA ±5 % F.S., Linearity: Within ±3 % F.S., Load resistance: 0 to 250 Ω
External input
(2-output type only, switchable
with Output 2)
- <NPN output type>
NPN non-contact input
• Signal condition
High: +8 V to +V DC or Open
Low: 0 to +1.2 V DC
(at 0.5 mA source current)
• Input impedance: 10 kΩ approx.

<PNP output type>
PNP non-contact input
• Signal condition
High: +4 V to +V DC (at 3 mA sink current)
Low: 0 to +0.6 V DC or Open
• Input impedance: 10 kΩ approx.
Possible external
input function
- Emission halt / Teaching (Full-auto, Limit, 2-point) / Logic operation setting / Copy lock / Display adjustment / Data bank load / Data bank save, selectable
Sensitivity setting 2-point teaching / Limit teaching / Full-auto teaching / Manual adjustment
Incident light
intensity display range
H-SP / FAST / STD: 0 to 4,000, LONG: 0 to 8,000, U-LG / HYPR: 0 to 9,999
Timer function Incorporated with variable OFF-delay / ON-delay /One-shot / ON OFF-delay / ON-delay • One-shot timer, switchable either effective or ineffective <Output 1>
Incorporated with variable OFF-delay / ON-delay /One-shot / ON OFF-delay / ON-delay • One-shot timer, switchable either effective or ineffective
<Output 2>
Incorporated with variable OFF-delay / ON-delay /One-shot timer, switchable either effective or ineffective
  Timer period Timer range "ms": 0.5 ms approx., 1 to 9,999 ms approx., 1 ms approx.,
Timer range "sec.": 0.5 s approx., 1 to 32 s approx., 1 s approx.,
Timer range "1/10 ms": 0.05 ms approx., 0.1 to 999.9 ms approx., 0.1 ms approx., each output is set individually
Light emitting
amount selection
function
Incorporated, 3 levels (each level 25 to 100 %) + Auto setting [1 level (25 to 100 %) when using H-SP mode]
Interference
prevention function
Incorporated (Note 5), selectable either automatic interference prevention or different frequency
Various settings Hysteresis setting / Shift amount setting / Emission power setting / Display turning setting / ECO setting / Data bank loading saving setting / Copying setting / Code setting / Reset setting / Logical calculation setting / Threshold tracking setting, etc.
Protection IP40 (IEC)
Ambient
temperature
-10 to +55 ℃ +14 to +131
[If 4 to 7 units are mounted in cascade: -10 to +50 ℃ +14 to +122 or if 8 to 16 units (cable type: 8 to 12 units) are mounted in cascade: -10 to +45 ℃ +14 to +113 ]
(No dew condensation or icing allowed), Storage: -20 to +70 ℃ -4 to +158
Vibration resistance 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude (10 G max.) in X, Y and Z directions for two hours each
Shock resistance 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Emitting element
(modulated)
Red LED (Peak emission wavelength: 643 nm 0.025 mil)
Material Enclosure, Case cover: Polycarbonate, Switch: Polyacetal
Cable - 0.2 mm2 6-core cabtyre cable,
2 m 6.562 ft long
Cable extension - Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
(however, supply voltage 12 V DC)
Weight Net weight: 15 g approx., Gross weight: 70 g approx. Net weight: 60 g approx.,
Gross weight: 100 g approx.
Accessory FX-MB1 (Amplifier protection seal): 1 set

Notes:

1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
2) 50 mA max. if 5 or more standard types are connected together. (25 mA in case of 2-output type and cable type)
3) In case of using the quick-connection cable (cable length 5 m 16.404 ft) (optional).
4) If display adjustment was conducted, it is not in this range.
5) Number of sensor heads which is possible to be mounted closely in auto interference prevention function depends on response time as shown in table below.
Number of sensor heads which is possible to be mounted closely in different frequency Interference prevention function is up to 3 units.

Number of sensor heads mountable closely (Unit: set)

Response time H-SP FAST STD LONG U-LG HYPR
IP-1 0 2 4 8 8 12

Return to top

CONTACT US
If you have any questions, please select the option below to contact us or find answers.
CONTACT BY EMAIL / PHONE FIND LOCAL OFFICE SEARCH FAQ

Return to top

CONTACT US
BY EMAIL
Please click your area to select country or region



BY PHONE

FAQ


Requests to customers (Automation Control Components & Industrial Device) [Excluding specific product]
Requests to customers (Automation Control Components & Industrial Device) [For specific product]
Requests to customers (FA Sensors & Components [Excluding motors])
Requests to customers (Dedicated to industrial motors)