Business > Industrial Devices > Automation Controls Top > FA Sensors & Components > Sensors > Light Curtains / Safety Components > Ultra-slim Safety Light Curtain Type 4 PLe SIL3 SF4C > Option

Ultra-slim Safety Light Curtain Type 4 PLe SIL3 SF4C

Lineup
CAD data　 Catalogs　 Manuals　 Software
FAQ

Option

Option

Mounting bracket

Designation	Model No.	Description
NA2-N compatible mounting bracket	MS-SFC-2	Used when changing over area sensor NA2-N series to the SF4C series. The mounting holes of NA2-N series can continue to be used. Center mounting by a M6 hexagon-socket-head bolt is also possible. (4 pcs. per set for emitter and receiver) (Note)
Versatile bracket	MS-SFC-3	Two ways of mounting are possible. (1) Rear mounting which enables beam adjustment (2) Dead zoneless center mounting on aluminum frame (4 pcs. per set for emitter and receiver) (Note)
Intermediate supporting bracket for versatile bracket	MS-SFC-4	Used to support the safety light curtain in the middle. Be sure to purchase it when using the versatile bracket MS-SFC-3(optional) on SF4C-F55(-J05),SF4C-F63(-J05), SF4C-H28(-J05) or SF4C-H32(-J05). (2 pcs. per set for emitter and receiver) (Note)

Note :	The body of the safety light curtain is made of resin, so please take into account the expansion and contraction of the longitudinal dimension. When machining mounting holes, please check the actual product.

NA2-N compatible mounting bracket

MS-SFC-2

Versatile bracket

MS-SFC-3

<Rear mounting>

<Dead zoneless mounting>

Intermediate supporting bracket for versatile bracket

MS-SFC-4

Control unit

Designation	Appearance	Model No.	Description
Slim type control unit		SF-C13	Use a discrete wire cable to connect to the safety light curtain. Relay output. Compatible with up to Control Category 4.

Recommended safety relay

SF relay, slim type
SF series

Note：Please contact our sales office

for details on the recommended products.

Type	With LED indicator
Model No.	SFS3-L-DC24V	SFS4-L-DC24V
Part No.	AG1S132	AG1S142
Contact arrangement	3a1b	4a2b
Rated nominal switching capacity	6A／250V AC、6A／30V DC
Min. switching capacity	1mA／5V DC
Coil rating	15mA／24V DC	20.8mA／24V DC
Rated power consumption	360mW	500mW
Operation time	20ms or less
Release time	20ms or less
Ambient temperature	-40 to +85 ℃ -40 to + 185 ℉ (Humidity: 5 to 85 % RH)
Applicable certifications	UL/c-UL, TÜV, Korea S-mark

Y-shaped connector

Type	Model No.	Description
Wire-saving Y-shaped connector	SFC-WY1	Wire-saving connector for SF4C-F□-J05 and SF4C-H□-J05. Cables of emitter and receiver are consolidated into one cable for wire-saving. Wiring has +24 V, 0 V, OSSD 1, OSSD 2, output polarity setting wire (shield), large multi-purpose indicator input 1, and large multi-purpose indicator input 2 only. Net weight: 40 g approx. Power wire and synchronization wire are connected inside the connector. Interlock is disabled (automatic reset).
Cable with connector on one side	WY1-CCN3	Cable length: 3 m 9.843 ft Net weight: 200 g approx. (1 cable)	Mating cable for Y-shaped connector Cable color: Gray (with black line) Connector color: Black The min. bending radius: R6 mm R0.236 in Connector outer diameter: ø14 mm ø0.551 in max.
Cable with connector on one side	WY1-CCN10	Cable length: 10 m 32.808 ft Net weight: 620 g approx. (1 cable)

By using the Y-shaped connector, the least required wires such as power or safety output are consolidated into one cable. Man-hours taken for wiring is eliminated to the minimum. Construction times as well as wiring mistakes are greatly reduced.

Wiring diagram of control unit SF-C13

<For PNP output (minus ground)>
• Connect the safety light curtain control outputs OSSD 1 and OSSD 2 to S1 and S2 respectively.

Notes:
1) The above diagram is when using manual reset. If automatic reset is used, disconnect the lead from X2 and connect it to X3. In this case, a reset (RESET) button is not needed.
2) Use a momentary-type switch as the reset (RESET) button.
3) Unused wires must be insulated.

<For NPN output (plus ground)>
• Connect the safety light curtain control outputs OSSD 1 and OSSD 2 to S4 and S2 respectively and ground the + side.