AUTOMATION
CONTROLS

Search
Discontinued
Products


Panasonic Home Business > Industrial Devices > Automation Controls Top > Components & Devices > Relays / Couplers > Applications of Relays in Electronic Circuits


Applications of Relays in Electronic Circuits

Mechanical relays Selection Guide

1. Relay Drive by Means of a Transistor

1.Connection Method

If the relay is transistor driven, we recommend using the relay on the collector side.
The voltage impressed on the relay is always full rated coil voltage, and in the OFF time, the voltage is completely zero for avoidance of trouble in use.

(Good) Collector connection (Care) Emitter connection (Care) Parallel connection

With this most common connection, operation is stable.

When the circumstances make the use of this connection unavoidable, if the voltage is not completely impressed on the relay, the transistor does not conduct completely and operation is uncertain.

When the power consumed by the complete circuit becomes large, consideration of the relay voltage is necessary.

2.Countermeasures for Surge Voltage of Relay Control Transistor

If the coil current is suddenly interrupted, a sudden high voltage pulse is developed in the coil. If this voltage exceeds the breakdown voltage of the transistor, the transistor will be degraded, and this will lead to damage. It is absolutely necessary to connect a diode in the circuit as a means of preventing damage from the counter emf. As suitable ratings for this diode, the current should be equivalent to the average rectified current to the coil, and the reverse blocking voltage should be about 3 times the value of the power source voltage. Connection of a diode is an excellent way to prevent voltage surges, but there will be a considerable time delay when the relay is open. If you need to reduce this time delay you can connect between the transistor's collector and emitter a Zener diode that will make the Zener voltage somewhat higher than the supply voltage.

Take care of "Area of Safe Operation (ASO)".

3.Snap Action(Characteristic of Relay With Voltage Rise and Fall of Voltage)

Unlike the characteristic when voltage is impressed slowly on the relay coil, this is the case where it is necessary to impress the rated voltage in a short time and also to drop the voltage in a short time.

 
 
Non-pulse signal
(No Good) Without snap action
Pulse signal (square wave)
(Good) Snap action

4.Schmitt Circuit (Snap Action Circuit)

(Wave rectifying circuit)
When the input signal does not produce a snap action, ordinarily a Schmitt trigger circuit is used to produce safe snap action.

Characteristic Points

  • 1.The common emitter resistor REmust have a value sufficiently small compared with the resistance of the relay coil.
  • 2.Due to the relay coil current, the difference in the voltage at point P when T2is conducting and at point P when T1is conducting creates hysteresis in the detection capability of Schmitt circuit, and care must be taken in setting the values.
  • 3.When there is chattering in the input signal because of waveform oscillation, a RC time constant circuit should be inserted in the stage before the Schmitt trigger circuit. (However, the response speed drops.)

5.Avoid Darlington Circuit Connections.

(High amplification)
This circuit is a trap into which it is easy to fall when dealing with high circuit technology. This does not mean that it is immediately connected to the defect, but it is linked to troubles that occur after long periods of use and with many units in operation.

(No good) Darlington connection

• Due to excessive consumption of power, heat is generated.
• A strong Tr1, is necessary.

(Good) Emitter connection

Tr2 conducts completely.
Tr1 is sufficient for signal use.

6.Residual Coil Voltage

In switching applications where a semiconductor (transistor, UJT, etc.) is connected to the coil, a residual voltage is retained at the relay coil which may cause incomplete restoration and faulty operation. By using DC coils, there may be a danger of incomplete restoration, and a reduction in the contact pressure and the vibration resistance.
This is because the release voltage is 10% or more of the rated voltage, a low value compared to that for AC coil, and also there is a tendency to increase the life by lowering the release voltage.
When the signal from the transistor's collector is taken and used to drive another circuit as shown in the figure on the right, a minute dark current flows to the relay even if the transistor is off. This may cause the problems described above.

Connection to the next stage through collector

Return to top

2. Relay Drive by Means of SCR

1.Ordinary Drive Method

For SCR drive, it is necessary to take particular care with regard to gate sensitivity and erroneous operation due to noise.

IGT : There is no problem even with more than 3 times the rated current.
RGK : 1KΩ must be connected.
R, C : This is for prevention of ignition error due to a sudden rise in the power source or to noise. (dv/dt countermeasure)

2.Caution Points Regarding ON/OFF Control Circuits
(When Used for Temperature or Similar Control Circuits)

When the relay contacts close simultaneously with an AC single phase power source, because the electrical life of the contacts suffers extreme shortening, care is necessary.

  • 1.When the relay is turned ON and OFF using a SCR, the SCR serves as a half wave power source as it is, and there are ample cases where the SCR is easily restored.
  • 2.In this manner the relay operation and restoration timing are easily synchronized with the power source frequency, and the timing of the load switching also is easily synchronized.
  • 3.When the load for the temperature control is a high current load such as a heater, the switching can occur only at peak values and it can occur only at zero phase values as a phenomenon of this type of control. (Depending upon the sensitivity and response speed of the relay)
  • 4.Accordingly, either an extremely long life or an extremely short life results with wide variation, and it is necessary to take care with the initial device quality check.

Return to top

3. Relay Drive from External Contacts

Relays for PC board use have high sensitivity and high speed response characteristics, and because they respond sufficiently to chattering and bouncing, it is necessary to take care in their drive.
When the frequency of use is low, with the delay in response time caused by a condenser, it is possible to absorb the chattering and bouncing.
(However, it is not possible to use only a condenser. A resistor should also be used with the condenser. )

Return to top

4. LED Series and Parallel Connections

1) In series with relay

Power consumption:
In common with relay (Good)
Defective LED:
Relay does not operate (No good)
Low voltage circuit:
With LED, 1.5V down (No good)
No. of parts: (Good)

2) R in parallel with LED

Power consumption:
In common with relay (Good)
Defective LED:
Relay operate (Good)
Low voltage circuit:
With LED, 1.5V down (No good)
No. of parts: R1 (Care)

3) In parallel connection with relay

Power consumption:
Current limiting resistor R2 (Care)
Defective LED:
Relay operate stable (Good)
Low voltage circuit: (Good)
No. of parts: R2 (Care)

Return to top

5. Electronic Circuit Drive by Means of a Relay

1.Chatterless Electronic Circuit

Even though a chatterless characteristic is a feature of relays, this is to the fullest extent a chatterless electrical circuit, much the same as a mercury relay. To meet the requirement for such circuits as the input to a binary counter, there is an electronic chatterless method in which chattering is absolutely not permissible. Even if chattering develops on one side, either the N.O. side contacts or the N.C. side contacts, the flip flop does not reverse, and the counter circuit can be fed pulsed without a miss. (However, bouncing from the N.O. side to N.C. side must be absolutely avoided.)

Notes:   1. The A, B, and C lines should be made as short as possible.
2. It is necessary that there be no noise from the coil section induced into the contact section.

2.Triac Drive

When an electronic circuit using a direct drive from a triac, the electronic circuit will not be isolated from the power circuit, and because of this, troubles due to erroneous operation and damage can develop easily. The introduction of a relay drive is the most economical and most effective solution. (Photo coupler and pulse transformer circuits are complicated.)
When a zero cross switching characteristic is necessary, a solid state relay (SSR) should be used.

Return to top

6. Power Source Circuit

1.Constant Voltage Circuit

In general, electronic circuits are extremely vulnerable to such phenomena as power supply ripples and voltage fluctuations. Although relay power supplies are not as vulnerable as electronic circuits, please keep both ripples and the regulation within the specification.
If power supply voltage fluctuations are large, please connect a stabilized circuit or constant-voltage circuit as shown in Fig. 1.
If the relay power consumption is great, satisfactory results can be achieved by implementing a circuit configuration as shown in Fig. 2.

2.Prevention of Voltage Drop Due to Rush Current

In the circuit shown in Fig. 1, rush current flows from the lamp or capacitor. The instant the contacts close, the voltage drops and the relay releases or chatters.
In this case it is necessary to raise the transformer's capacity or add a smoothing circuit.
Fig. 2 shows an example of the modified circuit.
Fig. 3 shows a battery-powered version.

Return to top

7. PC Board Design Considerations

1.Pattern Layout for Relays

  • Since relays affect electronic circuits by generating noise, the following points should be noted.
  • Keep relays away from semiconductor devices.
  • Design the pattern traces for shortest lengths.
  • Place the surge absorber (diode, etc.) near the relay coil.
  • Avoid routing pattern traces susceptible to noise (such as for audio signals) underneath the relay coil section.
  • Avoid through-holes in places which cannot be seen from the top (e.g. at the base of the relay).
  • Solder flowing up through such a hole may cause damage such as a broken seal.
  • Even for the same circuit, pattern design considerations which minimize the influence of the on/off operations of the relay coil and lamp on other electronic circuits are necessary.
(No good)

Relay coil currents and electronic circuit currents flow together through A and B.

(Good)

•Relay coil currents consist only of A1, and B1.
•Electronic circuit currents consist only of A2 and B2. A simple design consideration can change the safety of the operation.

Hole and Land Diameter

The hole diameter and land are made with the hole slightly larger than the lead wire so that the component may be inserted easily. Also, when soldering, the solder will build up in an eyelet condition, increasing the mounting strength. The standard dimensions for the hole diameter and land are shown in the table below.

Standard dimensions for hole and land diameter

mm

Standard hole diameter Tolerance Land diameter
0.8 ±0.1 2.0 to 3.0
1.0
1.2 3.5 to 4.5
1.6

Remarks

  • 1.The hole diameter is made 0.2 to 0.5 mm larger than the lead diameter. However, if the jet method (wave type,jet type) of soldering is used,because of the fear of solder passing through to the component side, it is more suitable to make the hole diameter equal to the lead diameter +0.2mm.
  • 2.The land diameter should be 2 to 3 times the hole diameter.
  • 3.Do not put more than 1 lead in one hole.

Expansion and Shrinkage of Copperclad Laminates

Because copperclad laminates have a longitudinal and lateral direction,the manner of punching fabrication and layout must be observed with care. The expansion and shrinkage in the longitudinal direction due to heat is 1/15 to 1/2 that in the lateral,and accordingly, after the punching fabrication, the distortion in the longitudinal direction will be 1/15 to 1/2 that of the lateral direction. The mechanical strength in the longitudinal direction is 10 to 15% greater than that in the lateral direction. Because of this difference between the longitudinal and lateral directions, when products having long configurations are to be fabricated, the lengthwise direction of the configuration should be made in the longitudinal direction, and PC boards having a connector section should be made with the connector along the longitudinal side.

Example : As shown is the drawing below, the 150 mm direction is taken as the longitudinal direction.

Also, as shown in the drawing below, when the pattern has a connector section, the direction is taken as shown by the arrow in the longitudinal direction

2.When it is Necessary to Use Hand Soldering for One Part of a Component After Dip Soldering Has Been Done

By providing a narrow slot in the circular part of the foil pattern, the slot will prevent the hole from being plugged with solder.

3.When The Printed Circuit Board Itself is Used as a Connector

  • 1.The edge should be beveled. (This prevents peeling of the foil when the board is inserted into its socket.)
  • 2.When only a single side is used as the connector blade, if there is distortion in the circuit board, contact will be defective. Care should be taken.

4.PC Board Reference Data

This data has been derived from samples of this company's products. Use this data as a reference when designing printed circuit boards.

Conductor Width

The allowable current for the conductor was determined from the safety aspect and the effect on the performance of the conductor due to the rise in saturation temperature when current is flowing. (The narrower the conductor width and the thinner the copper foil, the larger the temperature rise.) For example, too high a rise in temperature causes degradation of the characteristic and color changes of the laminate. In general, the allowable current of the conductor is determined so that the rise is temperature is less than 10°C. It is necessary to design the conductor width from this allowable conductor current.
Fig. 1, Fig. 2, Fig. 3 show the relationship between the current and the conductor width for each rise in temperature for different copper foils. It is also necessary to give consideration to preventing abnormal currents from exceeding the destruction current of the conductor.
Fig. 4 shows the relationship between the conductor width and the destruction current.

Space Between Conductors

Fig. 6 shows the relationship between the spacing between conductors and the destruction voltage. This destruction voltage is not the destruction voltage of the PCB; it is the flash over voltage (insulation breakdown voltage of the space between circuits.) Coating the surface of the conductor with an insulating resin such as a solder resist increases the flash over voltage, but because of the pin holes of the solder resist, it is necessary to consider the conductor destruction voltage without the solder resist. In fact, it is necessary to add an ample safety factor when determining the spacing between conductors. Table 1 shows an example of a design for the spacing between conductors. (Taken from the JIS C5010 standards.) However, when the product is covered by the electrical products control law, UL standards or other safety standards, it is necessary to conform to the regulations.

Example of conductor spacing design

Maximum DC and AC Voltage Between Conductors (V) Minimum Conductor Spacing
(mm)
0 to 50 0.381
51 to 150 0.635
151 to 300 1.27
301 to 500 2.54
500 or more Calculated at 0.00508 mm/V

Return to top


Catalog Download

RELATED INFORMATION Title Language File size Update
電子回路におけるリレー使用上の注意事項
各種リレー共通(パワー,安全,シグナル,高周波,高容量,インターフェイスターミナル)
JP 227.8KB November 17, 2022
Applications of Relays in Electronic Circuits
Power Relays(Over 2A), Safty Relays, Signal Relays(2A or less), Microwave Devices, High-capacity DC Cutoff Relays and Interface Terminal.
EN 131.3KB May 30, 2022
电子线路中使用继电器的注意事项 CN-Simplified 742.1KB December 21, 2022

Return to top

CONTACT US
BY EMAIL
Please click your area to select country or region







BY PHONE

Search Relays


Requests to customers (Automation Control Components & Industrial Device) [Excluding specific product]
Requests to customers (Automation Control Components & Industrial Device) [For specific product]
Requests to customers (FA Sensors & Components [Excluding motors])
Requests to customers (Dedicated to industrial motors)